วีดีโอ

Really good Professor. Truly evolving engineering at Cal Poly Pomona.

Wow! I loved how you used the fixed position of the high beam bulb holder to determine level, the nylon bushings, the string line to determine center, the cardboard alignment rig, etc!

THANK YOUUUU omg you are my savior!!!!!

Can you please tell me how will I do the bode plot for 1/(0.5s +1) according to the seven fundamental functions?

Maybe one day I’ll actually attempt doing this to my car.

Can't you just clean or replace the grips? They look disgusting :)

Diagonal cut spacers were a genius idea!

very nice

Details

I had the same problem, A couple of squirts of wd40 sorted it.

Just found out about these! Can’t wait to install them! Thanks for the video!

Amazing video! Curious - it looks like you only used the nylon spacers on some of the bolts on the inside of the bowl, but not others - was there a reason for this, and how did you decide which ones? I'm guessing this had something to do with adjusting the position of the lights, but I didn't pick up exactly how you did that . Thanks for making this video - it's really great, and your work was super clean.

Can you drive without it?

Great series

😍😍😍 I wish the whole series was available. What textbook is used for this course?

التكرار الترادفي هو تسلسل من قاعدتين أو أكثر من قواعد الحمض النووي التي تتكرر عدة مرات بطريقة من الرأس إلى الذيل على الكروموسوم. التكرارات الترادفية موجودة بشكل عام في الحمض النووي غير المشفر. في بعض الحالات، يمكن أن تكون التكرارات الترادفية بمثابة علامات وراثية لتتبع الميراث في العائلات. ويمكن أن تكون مفيدة أيضًا في أخذ بصمات الحمض النووي في دراسات الطب الشرعي. www.genome.gov/genetics-glossary/Tandem-Repeat

The face scrambler”

1. It is NOT legal, go to morimoto web site and read the detailed explanation about DOT regulations. My friend is a cop, he loves to give warnings for it. And you'll have no choice but to get new set of headlights. 2. Each and every headlight has a mark, indicating the center of of the bulb, I guess, you do not have a clue about it, so all your measurements are bogus, most likely the light is not in correct position anyway 3. incorrect headlight setting will blind upcoming traffic, and, if you cause an accident, you may go to prison Bottom line: you do not like your headlights - buy a better bulbs, DOT approved headlights upgrade for you car or a new car

Do you have any problem with mechanical vibrations from bldc and MPU6050 sensor readings?

Which coefficients for PID you used?

Gem of Lectures 🤌

Good day, Prof. Would it be possible to upload the rest of the lecture videos for System Dynamics

krita is shit, sketch book shit. what is wrong with developers

Hey... it's the bike guy....what don't you do :)

This is so technical. I love it

After this install, does your C light still turn on if you switch into parking lights on the lever? Great install video btw.

Good video, explained everything 😊

Hello Nolan, it's a very good intro to Matlab. Thanks.👍

Very interesting clip for whom that want to DIY.

Thank you for this video. it provided me with a good idea. I attempted to connect an ACC power from my engine bay, but I couldn't find any available wires to tap into from the fuse box. I then explored wiring it from a relay switch, but there were no vacant relay sockets, and it's dangerous to tap into a relay switch in use. Finally, I was inspired by your video to connect two wires to both the low and high beam lights with two fuse, effectively providing a constant voltage source.

The whining noise is there i dont hear the screetch but any idea what it might be? Im wanting to take it apart but ill have to get the time

Where do u put solenoid cable,if i use only for low beams,its not necessery to put it,right?

Tip: when splitting the light if there is loads of glue strings, get an old drill bit on eletric drill and just spin it and drag it thru it all, will collect it all on the drill bit, can put something else in there like a stick or something if you don't want to ruin a drill bit Also search clip removal pliers or Trim Removal Pliers they are exactly the same, and like $4 rather than paying the $17 or whatever they are

Man we need a tutorial on wiring, That is the part that is tricky in my opinion.

Looks very OEM. Fantastic retrofit. Also you did a great job showing the process of retrofitting.

All of them are shit! Make them better! 2020 34,000kms fk

why did ve take velocity as the output at pole = 0 and position for all other pole values?

I really like the baby steps approach of teaching and not assuming the audience know something (feels like the only prerequisite is English ). In the lecture you mentioned notes, was that for student who enrolled to the class at the time of the video or they are available to everyone on TH-cam?

Could you please post the table you are using?

You u don't need to drill nothing if u was using the retrofit minih1

I’m looking for a kool upgrade for a 2001 dodge van,, yall got any ideas

Dumb question can we instead just buy the 2018 forester headlight assembly will it not fit a 2014 sj forester?

What's the textbook for this class?

Hello friend! Did I understand correctly that you have one lamp in your fog lamps? In my version I have a fog lamp and daytime running lights, 2 lamps. In my case, I can turn off the second lamp responsible for daytime running lights and make a remount like in your video. Right?

The lights are getting ridiculous. Just blinding everyone on the road.

Hi nolan why you didn’t t put the headlights in the ovenn after applying new butyl sealant?

Bro that was a super clean work 😻❤️

great tutorial

Thats cool. I dont have the repair kit but i bought 2 little springs and i will install them between lever and brake body. I needed to see how i remove it from the brake, thx!

You can use Plastic wrap the outside plastic to protect it when working with it :)