- 1
- 446 178
JA R
เข้าร่วมเมื่อ 15 ก.ย. 2013
HP LaserJet Pro P1102w Printer(CE658A), How to configure wireless settings
HP LaserJet Pro P1102w Printer (CE658A)
How to Enable Ad Hoc, modify settings, reset to factory default or assigning IP Fixe on HP LaserJet Pro P1102w Printer (CE658A) without access to Modem.
(HP1102W CE657A is a little bit different but should work)
1) Check your settings, to do that, press and hold Cancel button for printing one configuration page
2) We can see that there are there are some personal settings
3) We need to restore the printer to factory-set default settings
4) Press the Power button to turn off the product.
5) Press the Power button to turn on the product.
6) The product begins to initialize.
7) During init press and hold the Cancel button and the Wireless button for 10 seconds
.../... until 2 LED lights blink together, and then release both buttons.
LED lights blink alternatively until only green led is on.
The factory default settings are restored.
8) Press and hold cancel button for printing one new configuration page
9) You can see that your printer report shows IP Address to 0.0.0.0, same 0.0.0.0 for subnet, default gateway...
And the Direct Print is off.
10) Now go on one computer of your wireless domain (wired or wireless).
And launch full software from hp support
11) Follow this simple steps! (I cut a little bit the waiting time)
12) Now close all windows and come back to your Printer P1102W.
13) Press and hold cancel button for printing one new configuration page.
14) Note carrefully : IPv4, Subnet and Ip Default Gateway and come back on your computer
15) It should be 169.254.xxx.xxx, modify your network settings as following...
169.254.XXX.XXX+1, subnet and gateway as on your last printed page.
16) Open your browser and go to the http site of the IP printer address.
17) Once you are in the Printer Web-Interface,
Go to “Networking” and configure your wireless network and click
apply.
18) Configure back the TCP/IP Network Properties of your computer as origin.
19) Once it’s configured and working, you should be able to ping the printer with his new IP and configure it on all your posts.
20) That's all folk!!!
How to Enable Ad Hoc, modify settings, reset to factory default or assigning IP Fixe on HP LaserJet Pro P1102w Printer (CE658A) without access to Modem.
(HP1102W CE657A is a little bit different but should work)
1) Check your settings, to do that, press and hold Cancel button for printing one configuration page
2) We can see that there are there are some personal settings
3) We need to restore the printer to factory-set default settings
4) Press the Power button to turn off the product.
5) Press the Power button to turn on the product.
6) The product begins to initialize.
7) During init press and hold the Cancel button and the Wireless button for 10 seconds
.../... until 2 LED lights blink together, and then release both buttons.
LED lights blink alternatively until only green led is on.
The factory default settings are restored.
8) Press and hold cancel button for printing one new configuration page
9) You can see that your printer report shows IP Address to 0.0.0.0, same 0.0.0.0 for subnet, default gateway...
And the Direct Print is off.
10) Now go on one computer of your wireless domain (wired or wireless).
And launch full software from hp support
11) Follow this simple steps! (I cut a little bit the waiting time)
12) Now close all windows and come back to your Printer P1102W.
13) Press and hold cancel button for printing one new configuration page.
14) Note carrefully : IPv4, Subnet and Ip Default Gateway and come back on your computer
15) It should be 169.254.xxx.xxx, modify your network settings as following...
169.254.XXX.XXX+1, subnet and gateway as on your last printed page.
16) Open your browser and go to the http site of the IP printer address.
17) Once you are in the Printer Web-Interface,
Go to “Networking” and configure your wireless network and click
apply.
18) Configure back the TCP/IP Network Properties of your computer as origin.
19) Once it’s configured and working, you should be able to ping the printer with his new IP and configure it on all your posts.
20) That's all folk!!!
มุมมอง: 446 200
somehow i've managed to fix with your steps Thank you man thank you very much it was Awful to fix the problem 😅😅
Información en español
Thanks a lot. You are the best.
i print from (direct wi-fi) and its so bad.this solution to print from your wi-fi network ?
I love it! I was a bit worried about the setup because I read mixed reviews, but the setup was so easy th-cam.com/users/postUgkxciSwynMJ7PnUvvx11rewiu-yFBkZTl53 , I literally set it up in under 5 minutes. The print quality is amazing and it comes with 6 months free of instant ink which is definitely a plus! This is an amazing all-in-one printer for pretty cheap, I 100% recommend this and would definitely buy again.
I can't hear anything at all.
Prix
This worked for me! Thank you thank you so so much!
Can someone provide a link to the Driver can't seem to find the right one.
Nice. Thank you
Can we use it to print colour printing
is wireless printing possible using mac ?
how did u get to the 11 part how did u get that opened?
i got a mac how tf do i connect this bih ?
Thank You!!!! I was ready to go buy a new printer...you made it so easy!!
Thanks bro, you saved my work today! Abraço do Brasil!!
Quick, simple, and straight forward! Thanks for posting this!
No sound.
Go laser jet mfp m29w
where is the drivers link ... too much talk no walk
Thank you a lot <3
Alright guys, just wanted to add a comment about my experience with this printer. I had a lot of trouble setting up wireless printing option since the cable connection worked just fine. I would always get a blue blinking light on the printer after running the wireless configuration setup. Tried so many different things and this is what worked for me at the end. It was about the wireless router. Most of the new routers work on both 2.4 and 5 GHZ. This particular printer works only with 2.4 GHZ frequency. And that is what I needed to change on my router. In the router settings in my browser there are 2.4 and 5 GHZ edit tabs. In the 2.4 GHZ edit tab there are two modes. The default mode was 802.11 g/n. I changed it to 802.11 b/g/n mode and voila. The problem was fixed. I ran the wireless configuration setup for the last time and the printer was able to connect to my router. The cable was no longer needed. Hope this helps you as well and fixes your issue with this printer. Happy printing ;-)
Love it! Good looking
Thank you for your help. It very useful for me.
Thank you! A very useful video. I had connect to a new Wi-Fi network. The old router had crashed. In half an hour I managed to reset my P1102w to factory settings, and after that it was easy to follow your steps and reinstall the printer. I really appreciate your effoprt!
Up to where your connection failed mines didnt and is now working thank you very much
Thank you so much for your video! I had to reinstall my HP 1102w because it stopped working wirelessly. I tried the instructions on the HP website and got nowhere. I followed the instructions in your video and now can print wirelessly from all my devices. Thank you!
Thank you this really helped alot!!
Is it me or there is no sound on this video?
It’s hard to set up Wi-Fi
Thank god u help me alot!
I found out why I could't Connect to my WiFi. A Space Character in the WLAN Name causes Problems! For example: "Mikes WLAN" Changing the Name to "Mikes_WLAN" worked for me! Now I am connected and can put the printer in a Other room
you spared me from a headache, appreciate for sharing
thank you;)
Works great in Ubuntu found the driver automatically. Its a fast printer.
Je n' arrive pas a installe mon imprimante hp laser 1102
Je n'arrive pas a installe mon imprimante hp laser 1102w
where do you get the software at cuz im looking for it
Sir sofware kaha say mily ga kiya name ha sofware ka?
I tried to press and hold the cancel button and the wireless button, it didn’t work
im glad i found the solution here thanks and god bless you
Don't waste time. No voice no solution. Didn't work.
were same model nut keeps printing two pages of configuration cant show the alternating or together light of two leds
Thanks this helped me. It worked! I now have a working $10 laser printer.
I like it wwwwwwwwwooooooooooooooooowwwwwwwwwwwwww
just make every thing worse
nao emtedi
Tenho uma impressora dessa 1102w....fiz tudo que se pode fazer: limpei a solenóide, inverti a borracha que puxa o papel, estiquei as molas da bandeja e mesmo assim o defeito continuava (puxava o papel um pouco e parava). Daí, observei que existem duas travas embaixo da bandeja e percebi que, justamente a trava do lado que amassava um pouco o papel, estava fora do lugar. Fiz um pouco de força e a coloquei na mesma posição da outra. PRONTO, RESOLVIDO O PROBLEMA !👍👍👍
This printer is a POS. HP should be ashamed every putting it on the market.
After 4hours of trying to get this printer to work I finally did it. First I reset the printer as shown in the video and then paired it with my router. It just connected. I had tried this before but without resetting the printer. No installation needed in Windows 10
i could made it work on my network, my printter is a LaserJet p1102w at the first try it don't work, but i did all steps from de installation software and it connct to my network
how do you get it connected to your wifi
@@genesisrobinson8058 i did the same steps from the video, and then i install the drivers for my printer but i Select wifi configuration, i did it 2 times and the second one it works
@@kanongdl3766 ok thank you so much
@@genesisrobinson8058 hope you can do it work too
@@kanongdl3766 what does it look like
Didn't do this but got mine to work by doing standard installation which ends without the printer connected to network, then upgraded firmware here: support.hp.com/us-en/drivers/selfservice/closure/hp-laserjet-pro-p1102-printer-series/4110394/model/4110306?ssfFlag=true&sku= followed by: When the update completes, click OK. If you connected a USB cable to update your network printer, continue with these steps remove the USB driver that Windows installed during the connection. Search Windows for ‘Devices and Printers’, then click Devices and Printers in the list of results. Right-click the USB printer device that matches your printer model, then select **Remove Device **. Disconnect the USB cable from the printer and the computer, then restart the computer. When I reboot I see a new printer installed under the name NPI****** (Laserjet Professional P 1102w) with ****** being the last 6 of printer's MAC ID. Thanks HP for supporting your products. Peace out.