วีดีโอ

Very nice

Very nice

I want to repair my Iphone 13 its nit getting network can you help me how I can send you to repair?

waterdamage phones should be data recovery only you just let the phone to dry out.s with out cleaning any things ? that’s worse and wrong ?

You let the camera man to stop than swap with the known good logic board.. i have work this kind of job and he didnt eben clean the pads with desolder wick and the jumper isn't fasned with UV glue, when he is heating with 450'c with 45 airflow(quick 861 DW) i doubt that his jumping will disconect...its a fake video, he might knows the way to do it, but its not the same board that that he's tested..

Thank you so much for reaching us for your question. This particular phone wasn’t too bad with the liquid damage and it was a plain water where this phone was dropped in . So first and foremost when you remove the camera and the screen and all the plates, then you can see how much water is standing inside if there is still a lot of water standing try to put it on a heat pad very low heat like 70° and leave it for like 1520 minutes pick it up several time between that and see if the water is evaporating but first you can just clean up the water whatever the visible water is standing there similarly leave the camera on the heat pad for around five minutes. Let it dry as well you know, clean up the connections all the Connections with 99% alcohol leave it to dry again and leave it the whole phone not on the heat on the side after all cleaning at least at least for a couple of hours just to make sure that moisture is left in the motherboard and then just put it back and power up the phone and see how it behaves. If the phone is damaged in a pool, which is a chlorine water or in a sea, that is totally different scenario and definitely definitely. You have to be with the motherboard and you have to wash the motherboard with the alcohol and then you know put it back and check the phone thoroughly , I hope I answered your questions

when you cleaned the phone, did you remove the board and put in alcohol, put on a heat pad or just leave it aside to dry?

Does this OLED after market display keep the 120Hz refresh rate? Thank you.

i fixed this using soldering iron

uwu

What about the bezel size?

Jeez🔥

WOW

iPhone 13 display price Please sir 😢

*PromoSM* 😎

Incell and oled display price?

He looks like the guy who would break your fucking phone if you piss him off

I absolutely love your videos! Please do as many video’s as you can, go into as much detail as you can. Such a big help. Love from uk

430 gradi? Hai distrutto tutto

whaaaaat u use 400 degrees for heating?!!!! this kill baseband and the phone will be short aaaaand that’s why some bads are missing cause of over heating

You could have just preesed vol down and power for 10 sec. Tsk tsk tsk.

Was it possible just to reball the ic or it wouldnt work

buy a preheater

philippine coin...nice one

are you in the philipines?

First of its baseband and cpu on the front of the board.. and 430 c with the nozzle pointing in on the board !? I am suprised that you didn’t kill the baseband 😮 try to point the nozzle away from the board if you play around with so high temp!

The heating should be 450 and air 50, and don’t need to use coins change hot air nosel to more smaller

Great! Job

Which soldering Iron did you use for the job - the Weller or the JCB, also what model is the Weller?

Wher are belongs

Relay amazing

Nice your microsoldring

Give me a subscribe i will subscribe back :) lets grow together here, also no need to replace the ic also only need to put a jumper in one place :) reball ic so that ic can get down much faster and not melt other components, also i would suggest getting some nice microsoldering tweezers from union repair :) so you wont bump any other components :) also use uv mask so when you put down the ic so wire doesnt melt .. keep at it bro!!!

When you fit IC Chip back to motherboard what type of liquid you use?

thanks

So I went through this and a few other videos, made the digitizer replacement repair and holy crap! everything still works perfectly! Except for my official Apple Smart Cover doesn't put the iPad Mini to sleep anymore. Can anyone tell me where I might have gone wrong?

Good

Ebay sells only 10 bucks!!! you can replace yourself!!! SAVE your money!

Goodie Goodie

Would it be possible to disconnect just digitizer, to save some power and use device without touch screen? I really do not need this.

please do not ago as deep as he did with the metal spatula. you can damage the LCD.

No soldering involved??

Nowhere in this video did it explain that at the bottom of the LCD is glued down with thick black adhesive strips! When he pulls the LCD off with the screwdriver, it comes away cleanly... When I did it, the black strips prevented me from doing so, resulting in the LCD cracking. Thanks for that! Douchebag!

DO NOT attempt this repair based on this video. This has got to be most deceiving video I've ever seen!

Bella cagata di video!

You left several steps out of the procedure first of all is to remove the 16 screws and metal plate that covers the battery. And the metal plate that secures the LCD and digitizer connector pin Connectors and the three screws. This would be helpful if you're wanting to actually show someone how to repair something. Disappointed in your shortcut demonstration which is really not helpful.

Don't you have to take out the 16 screws to change the screen ? I'm just saying , so far you're the only guy in TH-cam NOT doing that

Do you just stick the new glass on or do you need some glue or what?

Soldering iron? for what? i replace iPad screens regurly and never needed a soldering iron

whack video