วีดีโอ

i have a 2003 gt if i swap out my dash for another one will it cause pats issues ?

I know this is an old post but u wouldn’t happen to know the OD of those inner pipes you cut off?

I swear i did exactly what you did here but when i started unplugging the lines a lot of fuel was squirting out so i panicked and quickly plugged it back 😅. In the video not that much fuel came out compared to me. Idk what im doing wrong.

Hi Amel, can you please share your thoughts on Ford's Ecoboost 2.3L HP engine, as installed in recent model Mustangs.

I know what time it is

2010 f150 super cab 5.4 average 11 mpg 2 mile commute to work 30 mph speed limit. Is that normal?

hello, can someone please show me where does the ground harness gets connected from the frame? Mine is only atteched to the frame and the other end its just flying around next to the left side of the engine. Cheers

Is it a wise idea to drain the torque converter fluid? I've been told to avoid draining fluids from it, as it takes a while for it to refill and can damage the transmission...

What mounting bracket oK, did you use for the USB? Outlet

Nice beard 🎉🔥🔥

Where is link to buy?

Why does my e46 not have air vents?

Where can i buy your wheels? And you please show us how to get the recording on your phone automatically after drive stops plsv

Good choice on wheels. Look great!

Just now seeing your post. I have owned the #7 Penske GT since January 2016. It’s a great car with 6,200 miles.

Does anyone know what this black hose is called?? 3:48 Pls mine has a leak and I have no idea what it is called

Did you have idle issues after this?

So, how did you remove it from the engine? Mine wiggles but thats it.

I’m missing the grommet that covers the bell-housing

Dang! I have an 03 with 5.4 Triton. All i do is change the oil and it gets like 18

big favor plesae when you first start your mach 1 what are the rpms initially. mine are spiking to 2 or 2 1/2k i think my IAC is going bad.

sweet car you got there i have same one same color. your still looks nicer. hey where did you get the blower nozzle for compress air

Hi. I have a question. At 6:21. Where you fill oil three a shifter. Do you have to open up the shifter?

What did you do with the red cable hanging from your yellow input in the rear?

Didn't do a very good for me to remove driver side door

What brand of pads did you use?

Where did you get the trim for under the window?

Thanks! Just bought a bottle. I will apply the application on my E350 tomorrow! I'm hype!

You don’t have to remove the tires but it does give you more room to remove the screws

With all the metal you are welding on the frame that beast is going to weigh 12,000lbs when your done.

Lee Dorothy Jackson Kenneth Lewis Larry

My brother when u see true the top is time to get a new top period

What brand axle did you go with for the replacement?

Anderson John Perez Cynthia Garcia Kimberly

Thanks for a great video. Just ordered my head unit and will install this weekend. Unfortunately, the A301 DSP is no longer available. Any suggestions on a alternative?

No links?

How did you remove the quarter panel window?

How long does it last?

I dislike how these don't have Cabin Air filters. Since you had the one unit outside I got a rough idea of how to implement one.

Tinted everything other than what i cane here tonsee but thanks for saying uo front that youbwerent doing the back. Threw you a like for not wasting my time

After two years, what do you think? I’ve heard a good bit of negatives about it over time

Can I send you a picture of Mimi rear quarter panel for your opinion on repair vs replacing

Your in a fracking race or what

I have a 2004 325ci convertible. Getting the wire routed to the front was not easy as the seat doesn't fold down. I found there is a straight run on the driver's side where the wires went to the CD changer. I could easily get the video cable fished through the rubber grommet from the inside to the back and then pull the video cable through into the car and run it along the door panel up into the dash. There is only a small gap from the radio chamber, but again, it is okay to fish the wire through it. Go from the trunk lid across the back of the convertible storage tray then down to the CD changer location. The channel is just inside of the wheel well bump. I hope to make a video when everything is complete.

😮 Holy crap Amel !!!!!!!

Awesome video! I'm about to tackle an overheating issue in my 2001 Cobra. She has almost 200k miles so am figuring that I go on ahead and replace the heater core while I'm at it!

Forever Black...lasts for a year? 😂

No one changes a throwout bearing unless they just put a new clutch in and the bearing you just replaced is bad from minute one. In my history of owning 7 Mustangs, 5 of them manuals I have in fact had a brand new throwout bearing be defective and noisy. Fortunately, changing a clutch in a Mustang is really easy unless it is a Fox body with welded X-pipe/exhaust and long tubes.

Man this is so awesome. I gotta question though. In the previous video, how did you figure out exactly how far up the strut towers needed to sit? Did you measure off the mustang?

I clean my evaporator great video but that didn't solve my problem of not getting too much are in my vents came to find out the insulation in the back was covering my air duct in the back