วีดีโอ

What are the symptoms of bad fuel injectors?

Gonna be awful hard to ever get that coupler aligned perfectly, I think mainly due to the movement at the motor mounts. How about dropping that gearbox down, and using a pulley on it and a pulley on the flywheel/flexplate, with a belt between them. A belt will easily flex enough to smooth things out.

badass

Helpful and key not to block oil supply above the output shaft bearing, with gasket material...thanks.

PS, i liked and subscribed! 😊

Is your left big toe nail painted ?😂 j/k lol

In groups (and from others with small motors) ive heard to NOT run full synthetic on these engines. But as always, i take those words with a grain of salt. Great video.

Good video did you get the other gauge from china yet? lol I dont think you need a relay for that fan, it draws so little current

Thank you for your response. Really appreciate your advice

As you've added a hydraulic fluid filter, you obviously think it's necessary. My neighbour and I both own one of these and he is a very good mechanic and doesn't think the hydraulic filter is necessary as it's a closed system. Could you let me know please your reasoning why you think it is?. Thank you

There's a reason why Chinese equipment costs less. I wonder what all those things would cost if the machine was left at a local dealer to install ?

New subscriber here..I have ben thinking of purchasing one of these ...I have been doing some research and just like most things from China I am sure I am going to have to upgrade many many things in addition to grease fittings as well as lots of other things...-John

Can you show how the battery is routed , I'm tired pull starting mine

I had a 15 s80 and have considered getting another one so i wanted to see what all is involved with a timing service since it doesnt involve a water pump replacement (electric pump). My s80 got almost 40mpg. Wonderful car. Good video.

Great video .. Watched it all and i dont even own a Volvo lol

This is a big help, I’ve got an 89 Ramcharger and I can’t get it safety inspected due to that stupid turn signal/cruise/highbeam/ wiper stalk. Gonna move wipers to dash and go highbeam turn only at column. Don’t care about cruise really. This video was just in time. Now to find a good column.

Drag screwdriver on a magnet 🧲 any steel screwdriver is Magnetized Your welcome

I have 2 of these welders and they both have the same issue. The wire sputters, seems like the wire is getting pinched, I’ve already replaced the liner. I ended up buy a new welder because I couldn’t figure it out and didn’t feel like throwing parts at it, but I would like them repaired because they were my grandfather’s.

Calibración mm del platino

But youre forgetting that the bearing material is ground up in the oil now and not just where the bearing was

Folks ,when he says the cams will roll over. He means after you remove the tbelt , one of the cam[gears] may SPRING ! forard or back risk hitting the piston. Moving the crank just off tdc helps avoid bending valves. Although i never heard or had it happen . It seems like a good precaution.

Who did you buy the bearings from?

What type of noise does it make? Is it a constant noise while you’re driving similar to like a metal or metal? And besides noise, would it give me a high revving RPM

What type of noise does it make? Is it a constant noise while you’re driving similar to like a metal or metal?

I did the same job in 6 hours it was a pain. I got injectors from Autozone.

Old Hyster Forklift Gets a New Floor Pan Nice video I have also been a forklift operator like this, I can even drive a forklift operator's car Thank you very much for sharing Regards

How many hour does it take to take it off and put it back ..

I had a slight misfire on idle specially in the morning so decided to change my injectors, i did mine @ 120k KM bought same injectors from ebay $90usd, its been 8k km (6months) now with no issue...

I have an 89 almost the same as yours and love it. Paid only $3,500 Canadian and they sell for about 10 G here. If you got it for $2,500 , thats a steal cause their worth a lot more. mine has 89,000 km or about 50,000 miles on it. I love working on it doing many little upgrades and renos.

Nice Video ! Handy tools to use : Razor blade . Cookie sheet pan Tip cleaners / music wire . Fireplace bellows . Can of ether . Wire brush .

i would replace the seal.. to be safe than sorry

thanks so much for the help 🙌👍

If you can’t design a car with the fuel injectors on top of the engine, I don’t want the car because there’s no reason for this.

This is why I’m not buying this car. I look at things like this before I buy a car if it doesn’t have easy access I don’t buy it. I’m buying a car right now. I’m getting rid of my old car, but just because I was looking at this video I won’t be buying this car.

classic pigs, da, and judge getting paid and promoted while the victim has 2K people to listen to his story. gl man, thanks for the welding vids... about 20 min ago I just got my new to me garage sale $100.00 hobart handler 120 to join metal for the first time!

That's what you'd call a good deal

Man what kind of car is that yellow one

man no matter how good you are a random idiot can still mess up your day. good luck buddy, get well soon!

PLEASE see a brain specialist!! So many medical providers aren't experienced in detecting TBI's! I've experienced it with urgent care and doctors, twice! Literally told an urgent care provider that I had been hit in the head and I was given asprin, and the doctor only cared about what the scan showed!

Sorry to hear what your going through. Good luck with it all and rest up.

Damn brother, glad you are "ok" for what the outcome could have been.

What is it with every random person on the Earth thinking they need to broadcast to TH-cam, their life‘s story?

She crossed over into the opposite lane to clip you? Is there a hill or sharp corner right by your driveway?

Glad you're recovering. When I had a low side my knees swelled up real bad from the trauma.

Crazy!

Glad you are still alive!

So glad you made it through this one. Take your time and heal up. TH-cam videos can wait. We'll all be here when you decide to return.

Dang. Thankfully you didn't get seriously messed up. Drink drivers are selfish fucks

Angels watching over you and amazing humans taking care of you. From great Friends, family and healthcare workers truly been blessed with the community support ❤

Thankfully you came out relatively unscathed.. Another YTuber lost his leg... Thoughts are with ya for a speedy recovery.. Take it easy.. ✌🤙🤙