วีดีโอ

@@IffySignals thanks for watching.

@@speits84 deus 2 was able to hit the dime in single frequency and legend did not but both had no problems seeing the dime in multi frequency modes so I guess the deus 2 had the upper hand in this test since it was a single frequency test

What was your settings on the Legend?

@@billbarry2984 pretty much the only thing I changed from factory settings is i backed my first tone break down to 7, I changed the iron rejection down to 1, and i put recovery speed at 6. Everything else was factory settings.

@@ChrissyEis yes i have updated it.

@@billbarry2984 thanks for watching.

I get in the mood to do shake downs too every now and then. Im no where as good at it as you are though.

Thanks for watching

nope legend are turkish

Rutus is no where near the detector the legend is. It has gotten better with update but rutus is still a toy in comparison.

Yes. Completely lost signal at recovery 8 and above and completely lost it at 2 and below. Vdi stayed the same in 3-7 but 7 was really faint signal

I have also had the at pro and yes the legend is better it’s deeper and it runs in multi frequency. But the at pro is a good solid proven machine and is quality built.

I did. Not much difference in 4,5 and 6. It starting losing the target and only giving one way signals when ran below 4.

What did you have your iron filter set at?

@@billbarry2984 i have it on 2. I never run it over 3 and I never run it below 2

Thanks for watching

If I drop my recovery speed below 4 then it seems like the signal is delayed and you don’t hear a beep until the coil has already passed the target making me believe the target is in a different spot than it really is

@@lancemcilwainoutcastmetald5398 That is the trade off but pinpointing helps. I hunt with higher recovery speeds when I'm not concerned with depth. I use low recovery speed in areas where I suspect the targets I'm searching for are near maximum depth.

I did. All the single frequencies except 40 did pretty much the same as m2. M1 and m3 did not do as well. Deep target id set on 2 did the best every time on this particular target. I didn’t show them all because I was trying to keep the video from being too long

Thank you!

Out in the wild i do not know but in my test garden everything was better with it set on 2 so that is where i will start and adjust as needed from there.

Gotya.

I have tried it turned down and all the way up. Still couldn’t hit the dime

Yes. This is the LG 24 small elliptical coil

first of all, 10 inches for a DIME is really deep, even for the stock LG30... secondly, it is obvious that it is the LG24. The LG30 isn't tiny and narrow like that.

Thanks for watching

Are the bricks giving a signal on their own, swing over one and see if the brick effects your detector. 😊

@@billbarry2984 no the bricks do not. I have moved them repeatedly over the years when I have been asked and the results are always the same. I have been down that rabbit hole many times through the years.

Thanks for watching

Thanks. I have very mild soil everywhere around here and it’s hard to find natural mineralized soil to test in , so fertilizer was the closest thing I could think of. Our ground is so mild that even cheap detectors can hit 8 plus inch coins. My dads bounty hunter pioneer 505 even hits the deep stuff around here. Our main nemesis is heavy iron laden sites where unmasking is the #1 concern with detectors.

Yes im running the lg 24. As far as detectors, i have the legend and the double score and deus 2 and had the equinox 600 but it flooded a year after warranty ran out so i never replaced it. But i did like the performance on the nox 600 a lot.

@@lancemcilwainoutcastmetald5398 i have the Equinox 800, and have never taken it underwater. It's out of warranty too. Bought the Legend couple weeks ago. Liking it, but it's different. Half the reason for buying it was to tinker around with the settings. I think the Legend has more solid tones than the Equinox and its flute music. The Equinox has gave me a lot of coins though. The Legend still has to prove itself. 21 hrs with it so far.

@@RobNC-OGit took me a good while to finally click with the legend but now i ues it more than my other machines. My best program is park multi 2 in 60 tones with the first tone break set at 7, recovery speed 6 , disk ir at 2, deep target id set at 2 , volume 4 audio response 4. Sensitivity as high as you can run it and still be stable. Iron volume 3 and run in F to discriminate out ferrous but I still dig big iron but most of the time you can tell that it is big iron because it will be a chopped high tone with a little iron grunt off the edge of the target. Now silver is a different story. I can almost call a silver coin every time. It has a soft smooth high tone that says,HEY!! Im silver !!

I run the lg 24 coil almost all the time because it is so light. The original stock round coil is just too nose heavy to me but if you can handle swinging it then do it because it is crazy deep. It is deeper than my nox 600 was before it flooded.

@@lancemcilwainoutcastmetald5398 Agree with you. M2 seems to punch better for me also. I've been running Park M2, 4 tone, T1 break at 9, IF=2, St=3, Recovery Speed 4 or 5, AG=3. The LG24 is a good little coil. I like the LG30 too but my arm and tendonitis don't. But that LG30 is a real shocker, finds the stuff deeper like you said.

Thanks for watching

Thanks for watching Charlie. love your live streams. Even with no shirt on. 😂

@@lancemcilwainoutcastmetald5398 🤣🤣🤣

It hits it. All 3 multi settings hit it. I was just trying to keep the video from being too long. The only thing that didn’t hit it was 40khz single frequency.

Thanks for watching

Thanks 👍

Probably so but i think my hole may have gotten contaminated because my nox use to hit that bullet easily and now it will not hit it either anymore

Thanks for the info. I got a new legend and a lg24 coil to go with it so your video was very timely for me. 😊

​@@lancemcilwainoutcastmetald5398You should go back over the Target's with the Equinox and See if it still hitting the Targets and if it's does it then it will be the Settings on the legend detector that is needed to be Adjusted on the Targets that are Sounds like Iron Grunts and that's before the Separation Test....