วีดีโอ

The main gear bungees are strong because in a spray Pawnee there would be 140 gallons of spray in the hopper on takeoff. This makes the gear a bit stiff when there is nothing in the hopper. Make a normal power/pitch approach to arrive at the desired touchdown spot in a three point attitude all slowed up and ready to squat (from S&R page 302). Just before touchdown, level the fuselage to wheel land slowly and softly without a long hold off. If you force it on with too much speed you will get a rough hop/hop even if the wheels stay on the surface.

lol

Promo_SM

You can just google a dispensary, itd probably be faster

I sat in tug for 5 minutes , the pilot briefing me said next time you see this attitude you've landed! Spot on. The other advice he gave me was climb to 3500ft qfe, close the throttle and do a 360° turn. Yep that made me realise always land ahead if engine failure.

Have you tried changing the water pressure sensor? It's a fairly cheap part and you can find the part number on your manual.

Sadly, looking at the piping schematic it looks like this boiler was put in completely wrong and that’s why you’re having all these issues. I realize this was two years ago that you put this on TH-cam. I am a Navien professional.

The wrench is probably the outdoor reset not being connected. Do you know if you have one installed?

No still has issues

Did you ever figure yours out? I have the same unit and i am wondering how to work it as well. 2 story house and some rooms colder than others?

Part 2?

Dead psu

How do I bring down the psi

Where's part 2?

Thank you Dave for your timely reportage.

Red cap with bar is "never fail" floating gas gauge. We burned about 4 gallons.

You could never get into the Belle Haven Club.

Dave, great questions. I'd like to know as well how many pounds of food scraps are actually deposited, and, whose property is this?

Who knew you were such an influencer?

I have the same issue. The cover comes off easy just pull it off. Adjusting the ice size or fill water I'm still trying to figure this out.

en.wikipedia.org/wiki/Toggle_bolt

Great family spot

Love thhis

Replace icemaker

Wow

Wow

Is your dog's name Stormy Daniels?

What’s your outside antenna? That looks like an F-type connector which is usually found on coax for TV which is 75 ohms. 1) if that is the case it will give you an impedance mismatch to the radio which expects to see 50 ohms. 2) you need to have a resonant antenna for the band you intend to transmit on. I wouldn’t want to see you damage the finals in your HT. From what I see it looks like want an F-connector female to sma female...but again make sure your feed line and antenna are appropriate first.

Well none

Love this

You are viewing the info menu, not settings there. A is the supply temp 163ºF, B is the return temp 131ºF, J is the heat output 77%, etc. To adjust the temp setting you press mode once and then adjust it + or -.

goo.gl/maps/hKU7AVDhinmWjPf87 Pink House dirt bikes location

goo.gl/maps/vobZqr5J52i3x23p9 Nine Mile Run Trail

My mother was born on Tar Island Feb 18, 1922

Do all these valuable back and forth home tech "comments" go away with the new TH-cam rules? It will be a shame for the DIY community if Yes?

Hey, did you ever figure out the issue? And if so, was it due to the outdoor temperature reset sensor?

Hi If you r looking for the boiler temperature setting, you should press mode button once .

all suggestions ideas welcomed

new decision fix it, keep it, no tear down, resurface, install small Yagi antenna with rotator. Feed and electric lines go through unused flu- old furnace. Watch over the air digital HD TV for FREE. Watch for next youtube video

wow great Cotton Valley St Croix video!!! well done voice over!!!

Will upload Sense residential data- would the same Sense device work for a commercial site? A hockey rink?

this sense works

Ted goes deep

need a follow-up video of it working

VASI on the left side Runway 10 at KSTX