วีดีโอ

Nice Build at the Moment busy myself with this truck is there a a particular way wich light Goes where can’t find really a schematics about it

Awesome!!!

try tamiya extra thin plastic cement, it melts the plastitc back together

Im building my one for the first time but i still need a reciver what one should i buy for the stock vehicle

I received a faulty set. The helicopter would not connect to the controller. I filed a complaint with BG and after almost two months of waiting I received a new receiver board. Unfortunately, replacing the receiver board with a new one did nothing. The helicopter still does not fly. When moving the left stick upwards, the blades have a zero angle all the time.

In this helicopter, when moving the left stick up and down with the engine switched off, should the shield move up and down?

Hi Mike, having watched your video a number of times, I decided to purchase a1/32 Pajero. What I would like to see is how the electronics are done, and where do you get your batteries from. Kind regards Mike from Bristol UK

Where did you get these wheels and tires from ? Can’t find them anywhere

Mine won’t even take off without flying sideways and crashing into anything that’s there Banggood won’t refund me as they say it’s out of warranty I’ve only had it about a month

Suspension wont last long

how do you strip the wire? I always have trouble getting that part

don't break it it won't need to be repaired..just sayin

I know, old video, but do you remember what rpm motor you used? trying to figure out what I should use in mine

use a jumper instead?

I am so glad for your channel. Thank you for your inspirational videos!!!!!

Ahah 😂 look funny ! Good job for electronics integration 👍🏻

Parts are super micro. Extremely difficult to manage. Detail like this need to be in bigger scale. It's only for the utmost patience, not for everyone.

Hi ... I'm a disabled lady looking for an all terrain Mobility scooter,/wheelchair.. what batteries did you install... Was this because the old batteries were dead or ? And do you think the suspension and steering coloms (I think that's what the are called) would last ? As from I've seen online via a front wheel change video... It all looks flimsy? Great video by the way especially the wheelie you nutter 😂🕊️

Hello friend, how are you? I like your videos, I'm already subscribed to the channel. I have a Huina 583 wheel loader and I would like your opinion and guidance on upgrading it to make it better... engine, faster steering, proportional acceleration, etc. Could you help me with the purchase links or what should I buy? Thank you so much for seeing you Thank you, hug

I think a lot of people started with one of these. Hope you're still having fun with it

Mine starts with rotating blades after Power on. Without rc is connected. Any clue? It was proper flying at first.

Mine fried 2 servos so I got a metal one on order lol. I have tge drive shafts but the rear one is about 2mm too short. Im making a 3d printed sleeve to allow it to extend further without disconnecting

Turned out great. Love the blue color. I loved building mine; I found the process quite relaxing. Except for the drive shafts.

Tamiya could take a leat out of their book. I’m sure they could supply LED’s ( and proper bearings) considering how much their kits costs.

I’m looking at getting the same model of rims you have on your truck but tiny4X4s description says that they have a 3mm offset so I’m wondering does the body still fit with those rims or will the tires rub?

What RPM motor did you use? I didn't hear it in the video

Nice build. The red bits really dress up the chassis. I'm amazed that you were able to fit that giant battery in the rig. I use the same electronics, but with the 300 RPM motor which is a good baseline and the 120 mAH battery which is much smaller and lighter. I set up mine like a belly dragger with full droop. I have the same shocks on mine, but I removed the upper secondary spring and replaced the lower springs with optional soft springs. My shocks are set up with zero preload. I also swapped the 18mm wheels with smaller 15mm wheels and installed wheel weights up front. My X01 sits really low and has tons of flex. It literally defies gravity on my micro 4x4 course. It's actually a cheater compared to all of my "A" series rigs. Nothing else crawls as good. Thanks for the video!

Hello. I dont know english. That's why I didn't understand what you said. When you install that brushless motor, is there no need for ESC?

Brother.. Which Controller and receiver are perfect for this?

Yea can you take it apart to fit some lights now please ;p

I've ran across your videos in the past and finally gave you a sub. I love the Orlandoo Hunter kits and have most of them including some doubles. The M01 is an epic build and a great canvas for detailing as you know. I'm surprised you didn't order the M02 instead. Yeah they're basically the same, but that extra axle is wicked cool. I have yet to order an M02 yet as well but it's on my Radar. I just finished up the X02 and can't wait to run it. Cheers!

not std battery charge over charge or using 12vlt to get that speed i would say 12 volt as dont seem to slow down

Wow 😯

Nice work 😮

How much and whare can I get one please

I’m not sure if you’ve done it since this video, but one of the first things you should have done is replace the plastic shocks for the metal set… it makes a WORLD of difference!!!! Cheers

love it!

Does the servo still work

Thank you. this video was inspiring. I am considering making an 8x8 version of this truck!

This is so cooool! Like literally ice cool... but cooler! 🥶

🙂🙂🙂🙂😂

Great fun isn't it!! We love doing it in the garden to :)

I cant Programm it. Can you make a Video and Show it.

That looks great.

What reciever do you use for the frlite

where did you get all the leds from?

What RPM motor did you go with?

Seems like you're on the same track as me. I'm currently working on an 1/32 excavator. I want a full RC construction set. I do struggle with the electrics though 😂

I need one of these to help tidy up my desk! Great work!

What RPM is your rear winch?