- 97
- 15 196
Ray Ray
Canada
เข้าร่วมเมื่อ 11 ต.ค. 2011
Tie Lake BC Jam 2003
Playing Covers of Popular Old Songs at Tie Lake BC at Mikes Place
Some of our good old days I will always remember .
Some of our good old days I will always remember .
มุมมอง: 88
วีดีโอ
Dogs playing in the Cotton Wood river
มุมมอง 2382 หลายเดือนก่อน
Dogs playing in the Cotton Wood river
Kawasaki Mule Pro-Mx VFJ Performance ECU Reflash 3 month Review
มุมมอง 3.2Kปีที่แล้ว
Kawasaki Mule Pro-Mx VFJ Performance ECU Reflash 3 month Review
Kawasaki Mule Pro Mx oil in the Air Filter Fix !!
มุมมอง 1.7Kปีที่แล้ว
Kawasaki Mule Pro Mx oil in the Air Filter Fix !!
A good day with the dogs in the back yard.
มุมมอง 11ปีที่แล้ว
A good day with the dogs in the back yard.
Debbie and her 4 legged angels On the cottonwood River
มุมมอง 172 ปีที่แล้ว
Debbie and her 4 legged angels On the cottonwood River
The New Bridge points North and South over the cottonwood
มุมมอง 152 ปีที่แล้ว
The New Bridge points North and South over the cottonwood
Hey Ray Ray, you don’t have a heater installed in your mule do you? I can’t find that ECU and I’m wondering if I should just go ahead and tear the front end apart to get to it.
Yes I have a heater installed .Remove the front drivers tire or you can do it with the tire on .Look and you will see the ECU .Watch it vid again at the end and you will see.
Great video. I don’t think my fan is working. I used to hear it come on when idling now nothing and engine light has came on but went off when I started moving. I’ve replaced temperature sensor and fan is not hung up. You have any ideas of what I could check or do?
Good job, thanks for sharing.
Ray Ray thank you sir for making this video. Modified my Mx like you did. Works well!🎉
Thanks Steve It was a Factory problem that was never resolved by the factory.Now I run the right amount of oil .
Why wouldn't you unbolt the drive clutch and slip the belt over the shaft and bolt your clutch back on???
The books says to use a very expensive pulley holder in order to do that. If there was a cheap knockoff version of the tool or a safe way to hold it so you can torque it back down correctly, I'd go that route too. I'm still looking to see if there is a cheap way to get that pulley off and install it to the correct torque.
@chief1223 i literally unbolted mine.. slid the belt on and bolted everything back up. No tool needed
@@colbystancil how did you torque it back to spec
So that dash piece is the 4 pins or so and you say its velcroed on the upper section? Did you leave enough loose wire on the light that if you open dash piece back up, that you can pull it out enough? Thanks for the video!
Very nice!
I really appreciate you making this video. Damn EPA.
Thank You.
Thank you.
Awesome! Thank you!
what size ties do you have? i put 28s on mine
27 inch
THANK YOU SO MUCH!! I found this video on my search feed and was suprised that is about my work. I do absolutely appreciate the very indepth review seen here. THANK YOU for your support and time taken to do this!!
You are so welcome!
Nicely done, thanks for posting the vid. Its actually pretty easy to do once the pulley holes are tapped. Your mule needs a bath!
Thanks for the tip!
Thanks Ray Ray huge help as always
A dog's paradise. Well done
I’m so cute when I was a baby
Glad the trip went well, Can't wait to hear how the treatment works long term. Thanks for sharing this with us.