- 11
- 48 389
Simply Random
United States
เข้าร่วมเมื่อ 8 ก.ค. 2018
Just on here to create content and provide any information to the random things I do and I hope you find value.
วีดีโอ
Harbor Freight 2000 Lb. Pipe-Weld Swing-Away Trailer Jack 58045
มุมมอง 6K2 ปีที่แล้ว
www.harborfreight.com/2000-lb-pipe-weld-swing-away-trailer-jack-58045.html
Tractor Supply 5.5x10ft Carry-on Trailer
มุมมอง 9K2 ปีที่แล้ว
This is my take on the tractor supply 5.5x 10 ft carry on trailer. It includes my initial thoughts, experience and I go over my planned upgrades. www.tractorsupply.com/tsc/product/tractor-supply-55-x-10-ft-square-carry-on-trailer-55x10gwhdp-1358304?cid
Baja Reaction 150cc Slipping In and Out of Reverse
มุมมอง 1.5K2 ปีที่แล้ว
I know I did a bad job capturing everything but hopefully you get the idea.
Reading is not for everyone, clearly.
Someone can't read
I’m getting good results with carbon reinforced nylon.
What brand, %/type?
Good day, how well does the filament travel the way you have it inside the chain?
Haven't had a problem yet
This guys is stupid as can be
Dang
I've seen others who added a pipe for the jack near each of the rear wheels. Then they can move the tongue jack to the side with the flat tire and change it. I think it's a great idea so I'm going to do that with my trailer.
Hi, Are you using Orcaslicer with your Creality K1C?
im not sure but the Generic PLA Carbon - third from the bottom - means carbon fiber reinforced PLA
is it loud? Is it possible to stay in the room?
It is slightly noisy, I don't recommend sleeping in the same room.
Does it list a weight rating for the gate? Have a 1086lb atv and wondering if the gate will hold it.
I have a 800 two seater quad and it's about 1,000 lb. and the gate has no problem at all with it.
I got one recently and it has the front and back confused and prints everything mirrored from the correct orientation. Not a problem for all prints, but it means when I tried to print the side spool holder they sent pre-sliced it's reversed and the holes don't line up. So far creality support has done nothing for me except claim I sliced the model wrong (even though they sliced it). 🫤
Stepper motors with noise again ?
🤘🤘🤘
🤷♂️I'm doing nylon 12 Carbon Fiber on my K1 Max just fine
Standard nylon better x2
I got this also on my K1... got someone have an solution
I figured it out, I just had to adjust the tensioner for the belt, there's 2 bolts that were a little out of line which caused the belt to try to run crooked
@@simplyrandom9578❤
But is it printing good
Yup
I picked up one $200 Australian dollars put a new spark plug in it and cleaned out the Carby and it runs great best $205 ever 😊
Looking at buying one for my Side X Side . What is the rail height from the deck so i can see if my doors will open ? Thanks and great video
What is the Axle Weight?
Idd say they used that size pipe to prevent binding up over time
Yeah maybe
I just bought one of these from a local here in the Oklahoma City area. I didn't even know what it was called. I saw an image on pinterest that looked like it and followed it to your video. Thanks!!!
Mine is missing a bunch of parts. I don't have any of the electronics above the engine. No carburetor, intake manifold, air filter. Have you learned anything else about this machine since then? I could use your help.
A lot of parts are easy and cheap to find on eBay. Just search "baja reaction 150cc" and then the name of the part you're looking for and you should be able to find it
Very helpful video, Thanks for sharing.
Did you notice that about 10 came out and one went in? They are getting ready to deal with a potential threat. YOU!!!
Yep! Actually I ripped the nest right out of the ground. I wish I videoed it because My sprayer that I had sitting next to it got completely covered with them. I was in a bee suit by the way.
Get back. Yellow jackets are the insect equivalent to a gut shot grizzly bear temper wise.
I was in a bee suit. I do pest control so I deal with them on the regular.
@@simplyrandom9578 I have had to also on our farm in Alabama when I was younger.
This can be deadly.
Cool...but scary! Awesome!
That poor frog 😟
The gate doesn't hurt your gas mileage. Especially whe using a truck
I just bought one from TS and it had beating buddies on it
You got a great deal @ $450! I've had mine for a year and it's a lot of fun.
Is it difficult to move it around by hand? Wanting to purchase one to tow behind a fifth wheel so I want something thats easy to pick up the tongue and maneuver.
It's pretty easy for me to maneuver it around by hand providing them on a somewhat flat surface. When I hook it up I don't even try to hard to get close with the hitch I just pick it up and hook it on. I've also use it on my quad around the property collecting firewood.
They inject the antibiotics into the outside of the rear leg which always ends up on the round flat. That is likely an injection site. It should be removed for retail sale for sure. If you want to enjoy a steak, start with the sirloin and work your way forward on the cow.
Hope you kept your receipt. I'd take it ASAP.
Mig weld?
Yup
Nice video. Just what I needed to know. Also, the swing away Jack just bolts on instead of welding and if you wrap the frame with heavy tape before bolting it on you can remove it without signs of wear if you do decide to sell it.
Thanks. I got the weld on style. th-cam.com/video/vLe6qVKqmlA/w-d-xo.html
You could have welded that right in place it would have been fine The heat transfer for a quick weld on the end of the shaft would have been minimal .But thank you I needed to see what was in there and how it works .
Well shit! I thought I got a good deal, I paid 200 and I didn’t even get an engine!