วีดีโอ

In the workshop manual the gasket goes on top of the plate (see comment below which is wrong!)

Where i work we have the 16k hours one😂😂😂

It’s a trick bulb

There’s a circuit in the bulb that senses when he connects the terminals with his hand and turns it on

IOI

Pee-tow

So I changed out the switch because my brake lights weren’t working , only one that worked by the middle, after changing this the brakes all worked and after a few minutes stopped working again

Fake

Obviously not, but it would make for a good video

Yes

No I opened packs from france and regret it.

Very epic

My experience with this dash cam was not good, at all. I hardwired it to my car and it worked fine for a few months, then suddenly it would randomly cycle on and off until I physically powered it off. Reformatting the Vantrue memory card didn't work and neither did resetting the camera itself. I reached out to Vantrue and they had me update the firmware, which didn't fix it. Vantrue then asked me to send them a video of the issue, so I did, even they were stumped so they decided to send me a new one. Instead of hard wiring the new one I decided to use the cigarette lighter option instead, just in case, I even bought a new Vantrue memory card, and guess what? The camera did the EXACT same thing, except it happened a lot quicker, maybe a few weeks. I didn't even bother reaching out to Vantrue again. I tossed that camera in the trash where it belonged. Piece. Of. Crap!

infinity modulus 12" sub here.. if only it were that simple! checked mine top to bottom with a strong magnifier and flash light... no bad solder joints... mine developed a loud hum when powered on and a nasty thump when swithing in the crossover on and off...still works but the hum has made it almost unuseable

I just want to add the reason this broke for me is I slapped the fuel door shut which caused the little nub on the bottom of the plastic flapper to snap off. Don't slap or smack your fuel door shut like me otherwise you will be fixing it again lol.

Do you need a license to ride it….?

Could you send me the part number for That belt please “ I don’t know how to find that belt part # Plz”

Thank you!

Thats Neat

Very misleading due to all the missing steps. You can easily get your hand on the switch as shown in the video but there is no way you just reached up, grabbed it, and slipped it out!

The Akai GX 747 dbx was the top of the consumer line. There was the GX 747, then the dbx. Good find but will need a major restoration. All new capacitors, transistors, 2 tiny belts, cleaning, lubrication if needed, calibration. Good find.

W where

This is great. But how did you get the screw holding the skid plat to the top tank cover. I think it’s at 0:54 if your vid.

I saw that coming 🤦 it helps to stop cranking on puller and lightlyish tap the puller w hammer

"you wana kill my glass dont you"☝️😀

Can I use the fuse line to remove old gas?

Obgd pelo vídeo tirei bastante dúvidas, o meu está com problema na bobina do gatilho

I will give you the first comment.

What is the proper 409 running temperature? Wondering if I need to go with electric fans

Looks exactly same as my 42" deck, but I have a shorter (return?) spring that other models that are backwards from this as far aa=cable mounting, I don't see one on your's because your went too fast and hand held camera lol. does your's have a second short but strong spring somewhere that I didn't see in the video?

DNR watching from far away like 👀 haha. Dope video love to see it

Remove the deck for crying out loud. 3 simple points of attachment and the cable....It's so much easier to remove and replace the drive belt

You put the gasket in the wrong place it should have sat at the bottom of the steel plate not above it.

Friend i need some help. I got a water in oil in the propeller chamber[lower boot] on the same engine as yours 4hp 4t 2007. What can be the cause,can it come from the gasket under the small water impeller?

Luminescent is the word you're looking for. 👍☢️

Wow that looks tasty

That's really cool I'm a nerd for geods

Short circuit somewhere I would guess if alt dosent work. This is an old video surely you found the fix

I'm not sure you're doing it right. It looks like there's supposed to be some air in the unit. My '64 182 has what remains of a sticker on the shimmy damper. Referencing the parts catalog, near the front, there's a section showing all the placards on the aircraft. Sure enough, there's the placard for the shimmer damper. It says - "Fill with 74 cc of MIL-H-5606 hydraulic fluid at room temperature. This will allow correct airspace for fluid expansion. Do not overfill." So it looks like there's supposed to be some air in the unit. Not sure about this model though. It would help if we had some technical data to go on but it seems like if you totally fill it, it could burst if the fluid gets hot. Maybe someone will weigh in with the correct data? Dynetric - A&P, IA, Atlanta

1672 Alysha Way

So cool

Nice 👍😊

I eat Ramon knoodles!and I'm good!to me organic is for pretentious nutrition nazis!

No music while you’re trying to watch a video would be great

I was quoted $3850 by local JLR dealer

first mistake.... buying one.

Had a couple of these, they aren't bad, they get the job done

Cheaper than a set of 6 wrenches off the truck 😁

Fuel filter on the torsion bar? 😂

I love 911s