- 186
- 536 963
WINGS OF MACHINES
India
เข้าร่วมเมื่อ 25 ธ.ค. 2017
Science & Technology
Indexing Type Tool Post (Malayalam)
Indexing type tool post. It is also called a square tool post or a four-way tool post. Four tools can be fixed in this type of tool post, and any one of them can be brought into the operating position. The indexing may be manual or automatic. The advantages are as follows. Each tool is secured in the tool post by more than one screw and, therefore, the rigidity is more. Frequent changing of the tool for different operations need not be done as all the four tools can be clamped at the same time. The disadvantage is that skill is required to set the tools, and it takes more time to set to the centre height.
มุมมอง: 163
วีดีโอ
Lathe - Single Way Tool Post
มุมมอง 15114 วันที่ผ่านมา
Single way tool post It consists of a circular tool post body and a pillar with a slot for accommodating the tool or tool-holder. A ring base, a rocker arm (boat piece) and a tool-clamping screw complete the assembly of this type of tool post The tool is positioned on the boat piece and is clamped by the screw. The centre height of the tool tip can be adjusted with the help of the rocker arm an...
Tailstock
มุมมอง 16821 วันที่ผ่านมา
It is a sliding unit on the bed-ways of the lathe bed. It is situated on the right hand side of the lathe. It is made in two parts namely the 'base' and the 'body'. The base bottom is machined accurately and has 'V' grooves corresponding to the bed-ways. It can slide over the bed and can be clamped at any position on the bed by means of the clamping unit. The body of the tailstock is assembled ...
Worm and Worm Wheel Gear Mechanism
มุมมอง 186หลายเดือนก่อน
A worm and worm gear mechanism, also known as a worm drive, is a gear device that uses a worm and a worm wheel to transmit motion and power at different speeds and speed ratios. The worm is a special type of gear with screw-shaped teeth that wrap around a shaft, while the worm wheel is the mating gear. The two shafts are usually at a right angle to each other and don't intersect. When input pow...
Orthogonal Cutting and Oblique Cutting
มุมมอง 218หลายเดือนก่อน
Orthogonal Cutting and Oblique Cutting
Mechanical Engineering Objective type Questions Answers Part-2
มุมมอง 1123 หลายเดือนก่อน
Mechanical Engineering Objective type Questions Answers Part-2
Mechanical Engineering Objective Questions & Answers(Part-1)
มุมมอง 1443 หลายเดือนก่อน
Mechanical Engineering Objective Questions & Answers(Part-1)
Single Point Cutting Tool - Parts & Angles
มุมมอง 4916 หลายเดือนก่อน
Single Point Cutting Tool - Parts & Angles
CENTRE LATHE SPECIFICATION (Malayalam)
มุมมอง 4398 หลายเดือนก่อน
CENTRE LATHE SPECIFICATION (Malayalam)
INSIDE, OUTSIDE & JENNY CALIPERS #engineering #malayalam
มุมมอง 49211 หลายเดือนก่อน
INSIDE, OUTSIDE & JENNY CALIPERS #engineering #malayalam
GENERAL WORKSHOP & MACHINESHOP BASE OBJECTIVE TYPE QUESTIONS AND ANSWERS
มุมมอง 230ปีที่แล้ว
GENERAL WORKSHOP & MACHINESHOP BASE OBJECTIVE TYPE QUESTIONS AND ANSWERS
Thankyou ❤️
Thank you
❤❤❤
Thank you sir
Threads cutt nu mathram ano ith engage cheyyunna Feed kodukkanum lead screw veno
പഴയ ചെറിയ Centre lathe കളിൽ Lead Screw മാത്രമേ ഉള്ളൂ. അങ്ങനെയുള്ള മെഷീനുകളിൽ feed നും thread Cutting നും lead Screw തന്നെയാണ് ഉപയോഗിക്കുന്നത്.
❤
Thank you
Thank you sir 🤝💐
Thank you
❤️❤️❤️❤️❤️
Thank you
🎉🎉🎉
Thank you sir
🔥🔥
Thank you
Thanks sir
Thank you
❤❤❤
Thank you sir
❤❤
Thank you
❤️❤️❤️
Thank you
Very good explanation for old lathe nowadays this mechanism rarely used in modern lathes no mechanism like this
Thank you
Thanks sir👍🏼
Thank you
Super presentation. Tailstock to support other end of job, & tailstock spindle.
Thank you sir 🙏
👍
Thank you
Super
Thank you
Bro ഒന്നും മനസ്സിലായില്ല.
എന്താണ് മനസ്സിലാകാത്തത്.
Adipoli.. Very useful.. Iniyum videos prathikshikunu.. Instruments related.
Thank you
👍👍
Thank you 🙏
👍👍
Thank you 🙏
👍
Thank you 🙏
🎉🎉🎉
Thank you sir
👍🏼🤍
Thank you
❤️❤️❤️❤️❤️❤️
Thank you
❤️❤️❤️❤️
Thank you
👍🏻
Thank you
👍🏻
Thank you
🎉🎉🎉
Thank you sir
❤️❤️❤️❤️
Thank you
Very Informative
Thank you sir
🎉🎉🎉
Thank you sir
Audio❤
Thank you
☺️
Thank you
😊
Thank you
Pronunciation 🔥
Thank you
Thank you
🎉🎉🎉
Thank you sir
❤❤❤
Thank you
❤❤
Thank you
❤
Thank you sir
👍
Thank you 🙏
❤❤
Thank you sir
👍
Thank you
Very Informative
Thank you sir 🙏
👍
Thank you 🙏
❤
Thank you
Great❤
Thank you
Can I get your contact no
Bro എന്റെ ബൈക്കിന്റെ എൻജിൻ ഡ്രൈൻ ബോൾട് ഇന്റെ ക്രാങ്ക് കേസ് ചെറിയ crack ഉണ്ട് .....അലൂമിനിയം വെൽഡിങ് നു rate എങ്ങനെയാ .......അത് ചെയ്താൽ കുറേ കാലം നിൽക്കുവോ plzzz replyy ❤❤❤❤
Weld ചെയ്താലും കൂടുതൽ കാലം നിലനിൽക്കാർ പ്രയാസമാണ്.
👍
Thank you