วีดีโอ

You may have them backwards, I think the tweeter is meant to be towards the inside

Did you ever have a Job looking at missiles and ting?

I know a guy in Canada with this and it stopped working after only 4 months. No support no warranty repair available

Замечательные стойки для полочников! Единственное, вместо комплектной "жевачки" использовал двухсторонний нано скотч. И под шипы шайбы от In-acustik. Ну и в черном матовом цвете мне больше нравится.

The problem with Solidsteel is the top plate is just to small for large Monitor speakers. Only 6- 5/16. The speakers have way to much overhang. Making me worry about stability. If they had an option for a larger top plate, I would buy them but no go.

What’s the audio you’re using for this video?👀

At 1:51 we can see three extraction units, all of which are not in use! Welding fumes are seriously bad for your health, including cancer! In the UK there is the Health and Safety Executive (HSE) which enforces the law and provides information and guidance, see this link…. www.hse.gov.uk/welding/health-risks-welding.htm

I bought a pair of Lintons, I also absolutely love them!

The links don't seem to work.

Three years later and this is still the most informative and best video out there covering the stands. Thank you! One tip, your thumbnail here is rather lackluster and does not draw attention to this quality video.

Will this be able to drive JBL L100 Classic decently? ...in an approx. 11'x23' room (half of a 2-car garage space). L100 is conservatively rated at 90db sensitivity (3rd parties measured it to be more 92-93db sensitivity; similar to Klipsch Heritage's 3rd-party measurements of 94-95db [Klipsch is opposite, very ambitious & non-conservative 99db ratings]) Also L100 is 4ohm impedance. Anyone running L100 with this? Would love to hear your experiences.

You have the incredibly low friction bearing and high inertia platter, but then you control its speed with an inconsistent, and elastic, belt.

I’ve had the low noise feet for a few years under my DC Carbon. They’re still there!

Whats the biggest speaker these could support, would they take a dynaudio confidence 20? Thanks

This is just what i needed in my life. use a service such as smzeus!!!

At $18,000, with arm, it's just another super overpriced table which can be equaled by tables costing FAR, FAR, FAR less. However, listen to the sappy music, get your favorite Credit card and go into deep, deep debt. And yet, there are so many VERY overpriced tables now days. It has become PATHETIC !!!

They think about everyone who cares about their Music.

Have not had a chance to audition this phono stage, but have heard very good things about them. Glad to see them available thru Mofi. Thanks for this great post!

Unfortunately these are NOT solid steel , but hollow, and should change their name to something less misleading

They are designed to have the grilles on for frequency response? You not know this?

I couldn't tell the difference.

James Henriot should be credited more and is an absolutely genius. His phonostage equipment is better than any high-end hi-fi equipment on the world market. It extracts the full detail from your vinyl cart and transforms you "into the music" instead the music punching you head-on through your speakers. Also the nicest bloke in the hi-fi industry hands down. 10/10

i mean that’s brazing, not welding…. but it sticks the metal together ok

Sadly the Koetsu Jade isn't even close to a compliance match with the Stogi S 12 tonearm

so make a pair of solid steel !

I am the proud owner of 6 pairs of different and astounding models!

Spinning the platter before leveling it was not good .

How might I get the larger wood top plate? Are the plates available separately? Thanks.

Very nice! ... I have a Morch DP-8 tonearm, and will try to get it installed in the Woodpecker.

Check out my speakers I've made th-cam.com/video/BNzrzVP2shw/w-d-xo.html

Is that digitally sourced ?

I recently made a purchase from falcon and Jerry was very helpful, highly recommend.

Hi mofi...i just bought a pair of Warfedale Linton 2 speakers,and want to bring them back to life, I would like to upgrade the capacitors in them ,but I'm not sure what replacements I need could you advise me on what ones will work,it's my first time to refurbish any kind of speaker....but I'm good with a soldering iron,many thanks for your help.

👏👏👏👏👍👍👍👍

Is this the Mahogany version or the Walnut version? I dig them a lot!!!

Hmmmm...why are these MOFI videos suddenly showing up in my TH-cam feed...🤔🤔🤔🤔

Just not a fan of wobbly unpivot tonearms.

Hat jemand von euch das Video verstanden?

Complimenti Ben per la passione che ci metti Possiedo delle proac d15 , cosa pensi se prendessi le Linton ? Grazie

Buongiorno ! Possiedo delle proac d15 , secondo lei le Linton sarebbero superiori Grazie

Thanks for the great comparison! That is a quiet machine. My first RCM's vacuum sounded like a road drill. After a couple of records I had to plug my ears.

My dream turntable

I am from Venezuela, and I woul llike to know how much money does this masterpiece cost? I think it is a lot of money., impossible to buy.

I do agree!

This is a hella long video for a old fashioned recipe. That said, I’ll give this a try but will stir with ice then strain over fresh ice. 🥃

What turntable is that please.. anyone

This video is for the Woodpecker not the Volare! I goofed wondering why the platter looks different from the aluminum Volare! I like the gold weights better on this one! Is that available on the Volare? Haven't seen it as an option. What is the difference between the 2 platters? Thank you, larry

How are these speakers for a home theater surround sound system? Or are they best for music listening?

Hand crafted presswood with real Veneer ? Anyone answer that please ?