วีดีโอ

Hi, are the holes in membrane made by the staples holding it to the studwork not a source of air leakage?

There's so much bs in this video i got gas

Air changes per hour

This requirement has gotten so out of control that it is now bizarre. Yes, it is great to save energy by sealing every little hole and crack. However, how much energy is consumed in making all those membranes, patches, and tapes?

how about pipes that get hot like wood fire stove pipe? anyone has tips ?

Thanks so much! Best video explaining how to handle those elusive leaks! 💯

Just wondering where you can purchase one of these kits?

I happen to live in a passive house since 21 years now, pay 124 EUR per YEAR for the heating of 90 sq.m. and am happy to FINALLY see that the topic gets attention. Very good presentation!

Just started watching, but he's a great instructor. Even I understood. (Plus: I'll be more careful of balloons I buy for kids. Too old to keep blowing up same balloons ;~)

Great video. I suggest when feeling for leaks, dampen your hands with water. Makes them more sensitive to temperature change

I am in the process of tracing these sorts of leaks in my 3 bedroom terraced house, and it is amazing how much difference it has made, just sealing some very tiny leaks. Many thanks for this clip, which I really enjoyed watching. Certainly given me one or two ideas to play around with.

Every builder, architect and person building new home needs to attend classes like this. They would better appreciate the need to air sealing and blower door testing.

A more comfortable home. A more energy efficient home. Saving energy saves money on utilities.

I find scissors quickly gum up with Tesco (Pro-clima) tapes (because it's very sticky stuff), so have to use a knife. I guess it works OK with these isover tapes. Rather an making your own collars or depending on that dodgy bit of goop in the corners for the joist, just use pro-clima grommets: (roflex or kaflex). Available from green building store and ecomerchant in the UK. www.greenbuildingstore.co.uk/product-category/airtightness-products/grommets/ Seems to me he's making the backing piece excessively large, which just uses a lot of tape. Especially with multiple cables a proper kaflex multi-cable grommet is more reliable than trying to squirt goop into the bundle. It's useful to know what to do when you've not got the right grommet to hand (especially whilst builders merchants don't stock this really basic stuff) but using the right thing is quicker and easier.

Excellent demo with the balloons. It should be used to promote Passive Haus.

What a jerk....he must have given ye a ball of money

From Port Alberni in the Heart of Vancouver Island BC Canada passive house build th-cam.com/users/seumas2videos To date 37 detailed videos with material used Port Alberni's first Passive house (Passivhause) build in the heart of Vancouver Island British Columbia Canada. Passive House(Passivehaus) is considered to be the most rigorous voluntary energy-based standard in design and construction industry today. Passive house buildings consume up to 90 percent less heating and cooling energy than conventional building. The use of Passive House design software was used to gain the specs required to meet the performance standard for this location. House was constructed well above the current standards as outlined in the B.C. Building Code. Footings were widen to 36 inches(914 mm) due to low bearing soil conditions and additional rebar reinforcement added. 30 inch high (762 mm) high reinforced walls . Course sand placed inside foundation walls and mechanically compacted. Three layers of four inch *102 mm) thick Expanded polystyrene foam sheets with all joints staggered and tape were placed on top of compacted sand. The three layers of foam have insulation value of approximately R 50. A 20 mil layer of poly was placed over the E.P.S. sheets and taped and sealed. Four inches(102 mm) of 30 m.p.a fiber reinforced concrete was placed to form a slab over the foam based. Slab is isolated from concrete stem wall with four inches (102 mm) of E.P.S. to prevent thermal loss. All cold water lines are buried in the sand to keep them cool, hot water lines have been placed in the center layer of foam insulation to minimize heat loss. Wall plates compress to heavy beads of acoustic sealant between layers of vapor barrier to prevent air movement. The walls are double stud configuration set at 24 inches (610 mm) on centre and plates are spaced in a manner that yield a 20 inch (508 mm) thick wall. 1/2 inch (12 mm) standard plywood sheathing with Mento 1000 a three layer airtight vapor open house wrap( far superior to common house wraps) with 1/2 inch(12 mm) pressured treated plywood rain screen battens form the exterior surface. Intello smart vapour barrier was installed one third in from the inside wall to prevent condensation in this climate. Triple pane argon filled windows meeting passive house standards from Euroline were placed mid wall to reduce wind wash heat loss. All window openings have been splayed at 45 degrees to give a full wide angle view. Almost all the wiring and plumbing was kept inside of the vapor barrier envelope to minimize air leakage. Passive house standard requires air leakage not to exceed .6 Air changes per hour at 50 pascal. Zehnder comfoair 200 HRV has been installed with a 1000 watt air preheater .(92 percent heat recovery rate) House has been pre- plumbed for a heat pump water heater reducing domestic water heating cost significantly. Garage has been pre-wired for 40 amp/240 volt electric car charging station. House to be equipped with heat pump condensing dryer which requires no external venting,only a water waste line. George K Builder. © George K 2019 th-cam.com/users/seumas2videos

Still VERY relevant! A lot of upskilling needed throughout the construction industry.

Everyone should get this done at home

Nice presentation!

You should all be checking out a pre-made product called Quickflash www.QuickflashProducts.com that is available on the market. They have been around since 2001

wat even is this it looks like it was made with moviemaker

You could also show how to seal around downlighters.