- 24
- 226 759
arbafusion
เข้าร่วมเมื่อ 29 พ.ค. 2012
วีดีโอ
Gli Arbalete di III Generazione [Relatore: Davide Roi]
มุมมอง 1.5K11 ปีที่แล้ว
Serata a tema: un viaggio nella storia dei Sistemi Di Propulsione per Arbalete, dalla loro comparsa in Italia fino ai giorni nostri. Per organizzare questo evento nella tua città scrivici a: info.roisub@gmail.com
Allestimento Fusion1 - Strozzature [Roisub]
มุมมอง 6K11 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Allestimento Fusion1 - Montaggio su Arbalete [Roisub]
มุมมอง 77K11 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Allestimento Fusion1 - Finitura delle asole [Roisub]
มุมมอง 1.6K11 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Allestimento Fusion1 - Innesto delle asole [Roisub]
มุมมอง 2.1K11 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Allestimento Fusion1 - Serramento delle asole [Roisub]
มุมมอง 1.7K11 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Allestimento Fusion1 - Nodo delle asole [Roisub]
มุมมอง 1.6K11 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Allestimento Fusion1 - Gomme completate [Roisub]
มุมมอง 1.5K11 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Allestimento Fusion1 - Tagliare le gomme [Roisub]
มุมมอง 2.3K11 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Allestimento Fusion1 - Preparazione delle Asole [Roisub]
มุมมอง 1.3K11 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Allestimento Fusion1 - Conizzare le gomme
มุมมอง 85811 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Allestimento Fusion1 - Verifica su tabella [Roisub]
มุมมอง 2K11 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Allestimento Fusion1 - Prendere le misure [Roisub]
มุมมอง 7K11 ปีที่แล้ว
Per maggiori informazioni: www.roisub.com
Aggiungere qualche descrizione o audio?
Sir, lower rubber should be stretched ( pretensioned ) to certain lenght ( depending on thickness and length of upper rubber ) and then you should tie dyneema on it ... in perfect circumstances , when gun is loaded both rubbers should be extended to their optimal lenght ( in most cases it"s around 3x ( or 300%) of the original lenght ) ... The most simple setup is with two same rubbers ( same type and thickness ) , then you cut them to the same length (slightly less than 1/3 of the gun length from arrow pin to gun muzzle) then pretension lower rubber at (let's say) 2x ( or 200%) and then tie dyneema ! This way when gun is loaded you will have both rubbers stretched to the optimal length (300%) through the whole length of speargun, and you will have almost no recoil !
Exactly, very good remark ,and what about the shorter upper rubbers , how long they should be compared to the lower ones ?
Dyneema 2mm !!
Scusa il pretenzionamento non lo calcoli???????????
Scusa il pretenzionamento?????????
Antonio Smiriglio: taglia un pezzo del guida asta se è di quello adesivo e ci fai passare il dyneema in quella parte tagliata
in un fucile con guida asta come si puo fare?
100
quanto è lungo il fucile?
6.5
l'asta di quanto è.