- 149
- 407 823
cpstang24
United States
เข้าร่วมเมื่อ 12 ต.ค. 2006
Plasti Dip Removal Hack -- Wd40 and this Drill Attachment
Bought the multi interior drill brush kit off amazon and decided to try it on my plasti dipped wheels... this with WD40 took alot of the hard work out.. the trick is to really be quick after spraying the wd40 on.. if you let it sit its not as effective. Spray, wait 1-2 seconds and wipe.. otherwise let her eat with the drill...
มุมมอง: 47
วีดีโอ
3.5 Ecoboost Spark Plug Change 15-17 Expedition/Navigator/F150
มุมมอง 222 ชั่วโมงที่ผ่านมา
Replacing the spark plugs on my 193k mile 3.5L Ecoboost Expedition. Very easy procedure. Need a 5/8 Socket, extension, and socket wrench. 8mm socket for the ignition coil bolts. Preferable to do when the engine is warm to aid in removing spark plugs. Would spray PB blaster down the plug holes before removing plugs if you think they are going to break or be stuck in there. All of mine came out n...
How to Pull an Engine with a Winch and Engine Hoist By Yourself
มุมมอง 1812 ชั่วโมงที่ผ่านมา
E55 AMG Mercedes Lawn Ornament.. sold motor, no help so in a jam you can use your car trailer with a winch and put the engine hoist on the car trailer and hook it to the winch and give it a crank... Its not stupid if it works!
2015-2017 Ford Expedition and Lincoln Navigator Oil Change - How To
มุมมอง 4821 ชั่วโมงที่ผ่านมา
How to change the oil on your 2015-2017 Ford Expedition and Lincoln Navigator with the 3.5L Ecoboost Engine. Requires 6 Quarts of 5w30 Synthetic 1 FL500-S Oil Filter 8mm socket and 13mm socket required to drop the under shield 9/16 socket to remove the oil drain plug Oil filter wrench will help if the filter is on very tight, best to get the filter from underneath the truck.
2007-2017 Ford Expedition Water Leak in Doors Repair/Fix
มุมมอง 23วันที่ผ่านมา
Common issue on all 2007-2017 Ford Expedition models. The drains in the bottom of the doors get clogged, so the water comes in through the seal at the window and the water will sit in the door. Have to peel the lower door seal back and clean the drain at the bottom inside edge of the door.
Bought a Refrigerator to Drive everyday... Retiring the Town Car
มุมมอง 27วันที่ผ่านมา
Picked up a 16 Limited EL 4x4 Expedition for daily use. Going to document some common fixes and issues along the way. I know its not sexy exciting stuff, but we all need wheels to get around!
2003-2011 Lincoln Town Car Water Leak Inside Fix
มุมมอง 2314 วันที่ผ่านมา
Brief video on how to fix the ultra common interior water leak on the 2003-2011 Panther Chassis Cars. The wiper cowl seal on the passenger side fails and directs the water directly into the passenger side floor of the car.
New to me- Project 12th Gen F150 - Walkaround and Pull! Part 1
มุมมอง 2614 วันที่ผ่านมา
New to me 2012 F150. 220k.5.0L 2wd, RCSB. Rear Mount turbo kit coming soon. Work truck but also fun... are these still considered fast or worth building? Or these overshadowed by the Aluminum Trucks.
2018 Ford F150 VMP Odin Supercharged, Fore Fuel System, and LTH Headers - Pull and walk around
มุมมอง 39014 วันที่ผ่านมา
18 F150, 5.0L . Was brought in as a completely stock truck and now has a VMP Odin 2.65L Supercharger kit, FIC 1000H Injectors, Fore Innovations Twin pump fuel system, 93 and E85 Tunes, LTH Long Tube Headers, Roush Catback, and Billet OPG and CG. Lund Racing Tuned.
2017 Toyota Highlander V6 70-100 Run
มุมมอง 13928 วันที่ผ่านมา
Bone Stock Toyota Highlander. V6. 70 Mph Punch . These go pretty good for their power/weight. One of the best engines Toyota produced in my opinion.
F80 M4 Locked out of Trunk? Here is How to get it open. #m4 #bmw #trunk #lockedout
มุมมอง 56หลายเดือนก่อน
m4 hard top convertible. Trunk closed, bad battery, jump pack couldn't save it. So had to do it the old fashioned way.
Budget Return Fuel System S197 Mustang - Part 1- Regulator Mounting
มุมมอง 78หลายเดือนก่อน
Mounting regulator to the driver strut tower of my 2012 Mustang. This will be the same process for all 2005 to 2014 Mustangs. This will be a several part video process of converting a return-less fuel system to a Return Style for a Swap, or Increased HP goals with the car. Will show you how to make it return style using the stock fuel hat with a bulk head, as well as installing a twin pump afte...
Ford GT Supercar, Lamborghini Countach, 328 Ferrari Backdraft Cobras cruise and Walk around!
มุมมอง 174หลายเดือนก่อน
Lamborghini Countach Anniversary Ford GT and Heritage Model Aston Martin Ferrari 328 BackDraft RT3 Cobras
S197 Mustang Manual to 6r80 Auto Conversion Select Shift Wiring How To: Add Pins for Manual Mode!
มุมมอง 392 หลายเดือนก่อน
S197 Mustang Manual to 6r80 Auto Conversion Select Shift Wiring How To: Add Pins for Manual Mode!
VMP Ice Tank Unboxing for all 79-23 Mustang's - Spare Tire well mounted
มุมมอง 512 หลายเดือนก่อน
VMP Ice Tank Unboxing for all 79-23 Mustang's - Spare Tire well mounted
How To Build a Loft in your Shed -- Free Extra Usable Space under $200
มุมมอง 352 หลายเดือนก่อน
How To Build a Loft in your Shed Free Extra Usable Space under $200
HOW TO: Flip Key Programming for S197 11 to 14 Mustang. Easy!
มุมมอง 382 หลายเดือนก่อน
HOW TO: Flip Key Programming for S197 11 to 14 Mustang. Easy!
Cub Cadet ZT1 54" Deck - New to me Mower "unboxing"
มุมมอง 1662 หลายเดือนก่อน
Cub Cadet ZT1 54" Deck - New to me Mower "unboxing"
Badlands Winch with Amazon Winch Mount for Trailer Hitch - on my Land Rover
มุมมอง 982 หลายเดือนก่อน
Badlands Winch with Amazon Winch Mount for Trailer Hitch - on my Land Rover
12x30 Shed Delivery - Finally! from Shed's and More in FL
มุมมอง 1482 หลายเดือนก่อน
12x30 Shed Delivery - Finally! from Shed's and More in FL
S197 MAF Re-Pin for COYOTE or V8 Swap -- For V6 S197 HOW TO
มุมมอง 573 หลายเดือนก่อน
S197 MAF Re-Pin for COYOTE or V8 Swap For V6 S197 HOW TO
2003-2011 Lincoln Town Car Steering Shaft Upper and Lower Replacement HOW TO -- Crown Vic and GMARQ
มุมมอง 3213 หลายเดือนก่อน
2003-2011 Lincoln Town Car Steering Shaft Upper and Lower Replacement HOW TO Crown Vic and GMARQ
Town Car Steering Wheel Swap 2005-2011 Crown Vic and Grand Marquis- How To
มุมมอง 1K3 หลายเดือนก่อน
Town Car Steering Wheel Swap 2005-2011 Crown Vic and Grand Marquis- How To
Range Rover Sport HST Front Brake Rotor and Pad Replacement HOW TO- EASY INSTALL DO NOT PAY SOMEONE!
มุมมอง 8703 หลายเดือนก่อน
Range Rover Sport HST Front Brake Rotor and Pad Replacement HOW TO- EASY INSTALL DO NOT PAY SOMEONE!
2020 Range Rover Sport 3.0L V6 Twin Turbo Hybrid HST Oil Change HOW TO- DIY without Making a mess!
มุมมอง 1543 หลายเดือนก่อน
2020 Range Rover Sport 3.0L V6 Twin Turbo Hybrid HST Oil Change HOW TO- DIY without Making a mess!
2003-2011 Lincoln Town Car Tail Light Removal HOW TO - Easy, takes minutes!
มุมมอง 713 หลายเดือนก่อน
2003-2011 Lincoln Town Car Tail Light Removal HOW TO - Easy, takes minutes!
RARE CLK63 AMG Convertible in for Maintenance- M156 6.3L - Misfire and Oil Leak Diag
มุมมอง 1525 หลายเดือนก่อน
RARE CLK63 AMG Convertible in for Maintenance- M156 6.3L - Misfire and Oil Leak Diag
2022 Toyota Corolla Cross 0 to 80 .. Its actually Quick! CVT Trans
มุมมอง 3.7K7 หลายเดือนก่อน
2022 Toyota Corolla Cross 0 to 80 .. Its actually Quick! CVT Trans
2022 Nissan Altima 2.5 0 to 90 Speed Run... the Tach Never Moves LOL
มุมมอง 1.5K8 หลายเดือนก่อน
2022 Nissan Altima 2.5 0 to 90 Speed Run... the Tach Never Moves LOL
J&H Tree Service takes down my monster Cassia Tree.
มุมมอง 438 หลายเดือนก่อน
J&H Tree Service takes down my monster Cassia Tree.
Is that the second one down on the computer
replying to this for future people looking, its the bottom plug closest to the frame rail. I know we got this sorted already. Thx
th-cam.com/users/shortspAU5az798G0
Not bad for a stock Coyote without a 10 speed 🤝 can’t wait to see what it does with some boost
@HondaSkyline agreed thanks. I think it will be competitive enough with some boost, we will see very soon!
@@cpstang24 for sure man, especially with it being a SCSB. Subbed fs to see the progress
Whatsup brother nice video will you do a walkthrough of your install ?
@Monalissa5.0 thanks, and yes I will. I'll lay out everything I buy for hoses and fittings when I do the install. I should be doing this next month on the car.
Great Convo
I FOUND OUT THE HARD WAY, CUSTOM STEERING WHEELS ARE AGAINST THE LAW !
Where did u go.for.the tune if u dont mind me.asking
@robertsanchez6184 was a mail order tune I think it was APR was years ago I do not recall
Looks like golden gates estates in Naples fla
@@Robert-bg2nm it is not, close but wrong coast
How bout auto to manual?
@@parkecuc1192 you would just not plug in that plug in the center console or worry about those wires. The Manual doesn't look for any of that. Let me know if there is anything specific you were curious about.
@cpstang24 thank you for the info
That 1-2 shift was a bit rougher than normal. Should service your transfer case if you haven’t already
@@Jon-wn1yf was replaced by Porsche under warranty.
Hey mate . Do you still have the surround ?
@TomPolyzos I sold it on the w210 e55 page on Facebook sorry.
Acceleration 3 days and half 😂
coming from my Diesel Land Rover i was like woah this thing flies they give this much power to Mom's!! Lol
Where can i get the link for the part?
@@diosmanyacosta5317 I purchased my tow bar used off car-part.com but can check ebay or search local junkyard. I think I paid 350 for it to my door. They are double that new from Land Rover.
So helpful thank you much
What kind of wheels are those
@@jesusvilla3583 2011-12 mustang gt wheels 19 inch.
I'll be honest. When I saw the thumbnail of the stripped car, my first smart ass thought was, "I don't think I need to take it that far apart"
@andrewrife6253 hahahahaha I would of thought the same. One of those it's a easy job! Of course it is half the car is missing
Thanks a lot, man, this was very useful. However, the floor behind the driver’s seat in my car is completely soaked. I’ve taken out the tube like you did in the video, but water is still getting clogged back there, any ideas what I should do to help with the back?
Check the rear drain pipes too
@@Rx_farukh please where do I find the rear drain pipes?
sorry i am not much help i would do some googling and see if there is a how to on doing the rear drains.. thankfully i havent had to do that yet on the 3 c Class i have removed this tube on
Thank ypu..going to try it but does this affect anything at the dealer? Did you actually get something fixed before you did that??? Why did the light turn on in the first place?
Hi it does not. Dealer does same procedure. This was a service interval warning for oil change. I found after I do roughly 2 to 3 of my own oil changes the service light comes up because I do not reset it. The factory recommended service for oil changes was 10 to 15k miles per my LR dealer. I change it every 3000 or so. So I just take it as the normal oil change warning service per the mileage. These are not like the MBenz where they have the Alpha bet services with certain items to be replaced at X mileage intervals. Never was dinged for this by the dealer as my truck has been there for other recalls and services.
@@cpstang24 Thank you..just realized we are talking about two different things. I have the service engine light on but when I start it, it simply says service required. Or is it one in the same?
@@PabloZelaya service engine is different than service required. Service engine could be several things. Service required is just a way to get you to the dealer.
So many GTs in one location, I think this is the single closest thing to a place you can call heaven on earth.
Shelby gt500 burnout
Get the Hybrid version
Thanks so much for the vid. I recently purchased this exact model
Nice! Enjoy it. I put 20k trouble free miles on it thus far. Still just changing the oil every 3k miles. Good luck!
2 things you absolutely must do.... 1. Make sure the oil is at least warm when you extract 2. When you change out the o-rings.....lube them when you re-install. they will bind and snap.
If that’s stock… imagine a tune.
Yes bone stock right off the showroom floor
The car is much better than you at it
The car did all the work
Have you change the alternator
Thankfully no not yet. If you do not see any how to videos look for a newer BMW X5 or 340i.. it's the same engine.
Thank you
How were the mevotech supreme? I have a 2011 550 that I want to refresh, but don’t want to break the bank as I’m only putting 5k miles a year.
Nothing wrong with them. I've run their brand control arms on other cars and had no issues during my ownership. For something with that little mileage a year I would go that route.
Are you going to give the rundown on the build you've got going on?
Yes. Video to come soon. I'm almost done with it and I have taken videos/documented it so id probably say a few weeks and I will post it
I got one believe me u will enjoy it
Great happy to hear it. Excited to use it and add some accessories to it
I am having this problem too and so does my dad. same car and model. 2012 and 2013. The water is draining from the driver side front door and mainly from the ceiling in the center of the car through the ceiling light controls. My dads car fills so much when we drive after the rain we can hear the water moving when he brakes and goes forward. Is it the same process to remove the passenger front plug too? How hard is it to clear the rear drains?
thankfully just clearing the front drains usually takes car of the issues, yes same procedure for the other side.. But if you have sunroof drain clogs then that could be another animal. I know you would need to pen the sunroof and then with something thin but firm but not sharp feed the tool thru the drains to clean them out and pour water down the drain holes to help clear debris. The problem is the debris turns to muck and makes it hard to remove or clear up. Clear the front drains first and go from there.
@@cpstang24Hey do you know where the sunroof drains are ?
@@JimyOfficial yes. Have to open the sunroof so the front is popped up. And there is a drain tube on each side front corner
yo man, let's get outta here..
Have u raced any X5 M? I'm thinking about buying a 958.2 turbo
Our friend replaced this truck with a X5M... it was fast but I liked the Cayenne much better overall. With the tune and down pipes this would be a faster truck in my opinion.
Is that a 2020 Range Rover sport SE I thought the rear brakes has four calipers pistons and the front brake has six caliper pistons
It is a 2016. Only the SVR and 2017 HST received those brakes on the early L494. 2018+ received them as standard. The 2014-17 HSE/SE all trims received a standard brake caliper.
I had a whole puddle of water on the passenger side. A little bit on the driver side. Will this fix both sides ? Or are there any more drains to clean up or open up
Yes will fix both sides. Passenger side is less common it's usually just the driveside leaking over to god knows where. But start with driver side.
@@cpstang24 I just cut the rubber grommets on both ends. Had to replace all the CAN bus distributor boards because it got filled with water causing the car not to work at all
WHY T FREAK U USE 93 OCTANE JUST WHYYYYYYYYYYYYYYYYYY
Yes you are right. I should be using 87!
Why not? In Europe we should use 98 octane - equivalent american 93 octane
LOTS OF FOOLS IN THIS WORLD.
Stupid video like you
2nd to 3rd “gear” changes weren’t that smooth. There’s another acceleration where that sluggishness doesn’t happen
Agreed. It was not as smooth I hate to even compare this as I dislike cvt so heavily but it was not as smooth as the Altima.. this was far more Jerky and uncertain at times.
Did you have to do anything to the car system? Or did it work straight away? I have seen stuff saying you to need to plug the car in to add towing features
Nothing it just worked right away. No programming needed. Tow regularly with it with no hiccups. All trailer lights and my trailer brake works.
@cpstang24 thanks, installed today but not tested didn't have an adapter to convert back to 7 pin in the end 😂
@dufton21 haha that's always the way it goes! Glad you got it installed though that's the hard part!
9Y0 Cayenne Turbo? Which tune and who makes the downpipe?
Fabspeed down pipes and tune. Was a 2012 Cayenne Turbo S.
Looks like it was under a bloody black olive tree ...hope u were able to fix the rust ..looks pretty deep to me ..can u really fix that
hey just wondering if you ever found out what this noise was? My t56 magnum makes the same noise in 5th
Hi, Tremec said it just a side effect noise of lugging the car. So basically if you don't want to hear the noise drop down a gear or speed up.
@@cpstang24 how stupid I don’t see how they’d consider that normal, my car makes that noise no matter what RPM I’m in when in 5th gear, it’s so annoying
@ReaLisM579 yea its definitely bs but at the same time I always chalk it up to aftermarket parts. We get cheaper quality parts at higher than premium part cost. Ford for their 03/04 t56 probably was a $6500 trans after r&d and testing etc ..We pay half that now 10 years later for a t56 mag. That is essentially parts from china so it's expected to have some side effect. This is just my partial facto opinion
@@cpstang24 yeah I had less trouble with my stock t56 just hated the not chymes of it, but I have the RXT clutch as well, so that paired with this magnum is super noisy but hey, it is what it is lol thank you tho for the responce
@ReaLisM579 rxt absolutely aids in the sound. The twin disc's make a lot of noise and it resonates in these t56. Nature of the beast on that But I get it the noise is not always pleasurable. But no sweat good luck with the car
Are there brake wear harnesses on both sides that plug in with the abs speed sensor?
Yes there was one on each side. They plug in behind the fender liner/splash shield
@@cpstang24well time to look into this, I just changed out the speed sensors on all 4 tires and only had the brake caliper harness or the passenger side but each caliper had a brake wear sensor.
@jorgesevilla6582 ill triple check I know my land rover only had one on the driver side but I'm 90% sure this one had one on both sides.
You just saved me a bunch of money! Just fixed my leak in 20 minutes. Thank you
Awesome glad I could help!
Underrated video of the century. 1st built model after acquiring AMG ... The E55 W210❤🎉
Which way does it wind in please, not sure if mine seized
Lefty loosey. But please watch more of the video I found out when I got the e brake disconnect per the trucks dash board procedure on screen it auto pushed in.
@@cpstang24 i appreciate your reply, yes I'd watched it all the way through first, I have a clockwise piston tool, still anti clockwise on the opposite side im currently trying to do, thanks again
@daveshore6213 ok got it. If not take needle nose pliers with some pressure applied push down and twist
OMG! You have a 427 AC Cobra in the Garage! But back to the Rover. My wife has the LR3, it has actually been a great truck and I am thinking about getting this one with the diesel. Nothing scared me, I have a Ram Cummins but I found that oil extraction port interesting. Is that the recommended method to remove the oil? Is there a drain plug under the truck? How are you liking it after about a year?
Yes I do, hoping to finish it up and be on the road shortly with it. And I really like the LR3/4 but I have no complaints with the diesel as far as MPG or reliability at this point and time. The only issue I do have with it and seems to be a common complaint is the diesel fumes if you do not have the AC/Heat on Recirc. Sometimes coming to a stop at a light or certain scenarios with wind etc you just smell diesel fumes. Make sure you try to get a HSE LUX as those have rear AC vents in the ceiling and for 3rd row. Helps cool the truck down quicker. Mine does not and I wish I knew that back when I bought it. But I add DEF every 5-6500 miles, and just stay on oil changes. I tow with it and it tows great. As for the oil extraction. All the quick lube facilities do it that way, I am sure rhe dealer may if customer is waiting vs leaving the truck for other service I'm sure they would drop the under trays and drain it via the bolt at the pan. You can do it that way, but I had been using this on and off on vehicles for years and never really noticed any down side, plus I never get as dirty and gets done in half the time. Good luck on the search!
@@cpstang24 Thanks so much for all the info. I think diesel fumes are just a thing and all diesels have them. I actually love the smell. I know no one else in my family does. Good luck on the Cobra, she looks awesome.
Hello Sir , could you kindly put the part # of the hitch I want to get one and I don’t want to make a mistake when ordering it mine is 2017 HSE luxury. Thanks
Hi, part # is LR126253. Good luck!
I purchased mine used for I believe around 350$ + 125 shipping.
Glad to see your not using the 5w dumbass (30) in it. 5w40 is actually better for it anyways. Ford recommends 5w40 in severe duty applications which most people fall into without even knowing it. The biggest difference we see in the f150 3.0 is fuel economy comes down just a little. Just to note the f150 3.0 is based on the same architecture as the JLR, just different block casting. Im starting to make a bunch of 3.0 content. Another not is the timing components are identical between the two and fird is 1/4 of the JLR parts.
Very interesting because I just assumed ford took this from JLR and just called it a powerstroke and that was that. Because it got my mind going on a stand alone if you could use a ford ecu and harness to strip down to power this motor and trans or convert to the trans ford uses in the 3.0L f150 . Because I think it's a great engine for the size/power/tq and it gets good mileage for what it is.
@@cpstang24 Ford actually casts and produces these engines for JLR and PSA. They been being made since the early 2000's. They started out as a 2.7 in the JLR and even Ford vehicles in Australia. Ford did do a lot of updating when they finally was like yeah we are gonna use this in our trucks. If you were gonna try to stand alone it the 18-20 would be the years to do it with. Big but the trans computer is a standalone computer on the f150 it's not part of the ECU and the ONLY available transmission is the biggest pile of shit 10R80
Hi I want to buy an oil extractor how can I buy one?
Bought one on Amazon. It's called a MITY Vac