วีดีโอ

Some Deutz diesel inline engines have the number 1 cylinder at the flywheel end! Weird eh.

In my car i just turn the keys

I’m having the same issue with 2006 silverado. Can’t bleed it. So I left it. Will check tomorrow. I did go top of the fluid-it did go down a little. I replaced all the metal lines. There should be a law against using those metal lines that rust and have no coating.

Hey I have an 84 big red where the nut and washer fell off. Someone put a nut on it that wasn’t the right thread and lo and behold the threads are pooched. Do you by chance have an idea what thread size that axle is?

This video helped me understand how the carb in my 75 Toyota Pickup works, or should work, and that I need to warm the truck up. Thank you so much for the info and for presenting it clearly

GOOD VIDEO THANKS

You said the hydraulic pump doesn't have a filter?

Pitch black

How’s it been, how long did it take to get to you? I’ve heard horror stories of dodge off road but I want to trust them

These Ram trucks are crap. Im working on my sons 2002 Ram 4.7. Crank No Start. After a faulty radiator cap caused overheating. The ASD and Fuel pump relays don't activate. Its an electrical issue right now . Im now painfully tracing all the voltage and gnd wires first. Then checking all the sensors. No OBD codes were thrown. Hopefully the PCM isn't blown

4x4 is a v series

looks like a bad seal to me

every year? lol. ya nope not happening.

İs it welded full of gearbox..

Great video! Really good explanation. Thank you

Love these videos! I’ve got a 66 F100 with the 352FE in it myself and these videos have installed confidence that I’ll be able to do it myself!

You could’ve expand the spring 😅

Just bought them to try them out. I usually run Destination XT's for the snow but I'll put them to the test this winter

Do you put it in Drive? When timing, a automatic transmission? My Chevy sticker under the hood says to, does it make a difference? It also says put the conductive pickup wire from the timing light on the coil lead wire on the distributor instead of the number one spark plug, does that make a difference???

Is this a tubeless tire?

Its not really underground, its just under grass.

I have a 66 f100 4x4, I’ve known this pickup since it was new. I’m doing a full rotisserie restoration so, thanks I’m going to use some of these tips! Now how about someone doing a transfer case and, transmission video series!!!

You an take the step off pretty easy and then you don't have to remove the pedals or go in from underneath. You can go in from the top.

great video! Thanks for this ..getting into the job myself here soon.

Putting a piece of shop towel on the exhaust will prevent the hand burning. Figured it out after getting burned

Thanks for the video. Can we clean the whole outside of the engine, carburetor, and camshaft and everything else with brake cleaner? I have a used and very dirty push mower, and I removed the plastic housing cover, the plastic fuel tank, the 2nd metal plate housing, the air filter & cover, the spark plug, and the muffler. I covered the spark plug hole and the muffler hole with plastic bag and paper towel so nothing will get in the holes. It has a lot of grime and dirt all over, and I want to clean it all off but I'm not sure if this is something that can be done without damaging it somehow? If this can be done, is there anything else (electrical or other) that I need to cover with plastic to not get it wet and damage it? I wanted to get the advice from someone who knows about these things. Any help is much appreciated.

Good video thank you i have a 04 2500HD 6.0LS with 263k + miles runs great im thinking of replacing the same oil pump and timing chain as a preventive General maintenance. I’m having small issues with a dry start for about five seconds other than that runs quite smooth no knocking or anything else. Your thoughts sir 😀

When you install a helper leaf spring to a trailer, does it also go more towards the back like people often do for trucks? Or same?

When you lift up the body of the vehicle to weightlessness, could you use that to tell what kind of shape the leaf springs are in based on if they moved a bit or not from having weight on them? Thanks.

No special tools…. By the way here’s my depth gauge

Hello! I have a 78 F-150 that has wolverine locking hubs. They are leaking badly from worn seals. I can't find a replacement. Do you think it is possible to find seals for these or should I by new locking hubs? I appreciate the help

I assume you already tried a $10 oil pickup tube o-ring before doing all this? Those worn out oil pickup tube o-rings can be replaced by just dropping the oil pan and of course the pickup tube itself and im sure you know that already. Those oil pickup tube o-rings are a common issue after so many miles on these tucks and will cause lower oil pressure.

I turned my 1990 ram charger into a tailgate and top hatch by splitting the full hatch with little modifications to blend it in perfectly

I am having a ton of trouble finding caged wrist pin bearings for mine, it’s a 2002 with the 493 engine. The factory cageless do not work with wiseco pistons. And every cageless I’ve ordered is too big in diameter. Any suggestions?

It don’t bleed very fast hey. Very slow to come out

My son has them on his Gladiator, and says they are way better then the KO2s he had on his previous Jeep Wrangler. He drove both Jeeps in the same winter conditions anything from -30 snow and winter slush/rain conditions and the Mickey Thompson are much better in every category

You probably had the new spring backwards, thats why the front was longer...

How has it been running since? I've read that because you're supposed to use a temperature gauge or scanning tool that you should have the dealership perform this service. Trying to decide if I should take this on myself.

I magine another 54 lbs off with a Performer RPM intake? And a set of headers

Thank you best video.

😮My cuestion In spanish please. Me gusta la silverado 1500 2003 2004 2005 2006 cabina regular, quiero saber su comodidad. Y cuanta distancia se puede recorrer hacia adelante los dos asientos. Y con eso, cuantos grados se inclina hacia atrás. Saludos from Ecuador.

Thanks for the video, I assumed a drive to the auto parts store was going to be the longest part of this install… I was wrong, maybe the next ones will seat and live?

I was on the fence on this until I watched your video. Thank you.

It want let me open the link

Man made the same mistake 😢

They weren't all zero, some were 4 and 2. It says on the tune up label. Good video on where that wire is on that one. They are in different places throughout the years on tbi motors. They were around since 1981.5. Later wires are under the glove box by the heater fan, and others are in the engine compartment by the heater hoses other places too

Rebuilding my grandfathers 66f100 right now and these videos are saving my life haha.

That 450 lb-ft of torque is NOT the peak torque, but the torque at that rpm, 3,000.

Hi where I can get the swap parts for motor mount. I have 99 Durango and have the LS 6.0liter and have problem to fit the motor in the wagon. Thank you

What country are they made at?