วีดีโอ

A video on how to destroy your boat. This guy has absolutely no idea what he’s doing. You will be dumber after watching this drivel.

Nice vid. I have the same boat a few years older. And was aiming for a system 2 upgrade becauseI thought it was the same as my factory set up. But it looks like it lies somewhere between system 1 and system 2 from flow rite. How do you like it so far?

Good evening, how are you? I have a Mercury four stroker 150 hp 2021.. I wanted to know how I can deactivate the first stage of the trim so I can raise it but it... because my boat the side mirror is very inclined so I can't get enough height to gain rpm

Thanks!

do you have any pictures on rear mounted transducer?

What is the purpose of this gauge?.. I mean honestly is it necessary?.. can u not just turn your head and look to see if it's up or down?

You can get a new drop in seat from ranger all you do is call and give them the vin

Awesome band, Miss the Longbranch days, great memories!

Always remember seeing them at Longbranch in Raleigh, so talented! Miss you guys!

Thanks for you video.

Thank you, I think this will help - trim gauge isn't working, but the brown/white wire from the sensor is cut or broke off. Then on the opposite side of the motor, I have another wire coming out of the bottom of the motor housing, well it's a brown wire sticking out of tubing/casing with heat shrink covering where the casing stops so I can't see if there are two wires (with one of them brown/white). My sensor is grounded to the shaft so I am assuming someone had an issue (I'm not the original owner) and ended up splicing in this brown wire, leaving the ground wire coming from the motor just cut off. But your video puts me in what I think is the right direction.

Hey Steve great video! I have a 96 mercury 200hp efi that looks same as your 175hp. My trim doesn’t work and think it’s the sender. Can you please post up a link to the sender you used??

What brand and model seats are those. I'm looking to do my Comanche 492 here soon

What about the water that leaks in around the edges? I will have to measure how far the center storage goes to the front, but I am afraid it will leak in the dry storage?

Thanks for the tip Fish on

I've got the same Ranger seat from Ranger they are thin at the rolled part and rip

Thanks for your effort…….. and yes it has given me a good clue to my similar issue. 😊

Wish I could see or understand better how you laid the carpet and cut it etc

I have a Mercury Optimax 150HP 2002. The trim gauge doesn't work AND the motor send off an alarm after about 10~20 minutes of use saying Trim error. Cannot find a solution anywhere. Would the trim gauge not working cause this or is it likely the trim sensor?

Link for tray?

👍Nice job.

Awesome video. Thanks for doing this. I have a 95 482VS as well, and my seats are starting to show their age.

Nice work!

Would like to find the cds

Thanks about to same thing to my 461 how long did it take ? Can it be done in a day ?

Good job. I wanna take my seat out to look at the gas tank. May need a new fuel gauge sending unit etc. I do not see a way to take the seat off. 2000 Comanche 518🤷‍♂️

Yep, ran 2 grounds. Works well. Thank you

Thank you I will try this. I'm going to run 2 groungs.

how do you calibrate it?

I wish you would have actually shown the seats being removed .. I have a ‘91 482v and want to replace the seats .. it looks like a very tough job

Great tip! I had the same symptoms with my 2003 Mercury 150. The tilt sender unit on that model grounds directly to the shaft and 18 summers of salt spray caused it to fail. Wire brushing and a lot of dielectric grease fixed the problem. Like you, I couldn't find anything on this issue in boating forums or TH-cam. I really appreciate you posting this video. Saved me from buying a new sending unit and gauge.

I've got a '97 R80 and I'm planning on doing the same thing in a few weeks. Thanks.

Thanks so much for taking the time to do this video I was in the same predicament as you Got a quote for $1500 to redo the seats Was trying to come up with some other option and then I ran past your video thank you so much.

“I wanna be yours” is our wedding song. First heard Kindred Spirit at the Wild horse Saloon at Disney and loved them! Still have my CD.

It work's for me .Thank's

Thank you I’ve been lookin everywhere for something like this

Please post anything else you have by Slickerbilly?? I saw you guys play in Disney at the Crazy Horse--bought "Parts and Labour" brilliant music!

Thanks I have the same problem . I will try once I get on the hard.

Thank you, very helpful, I'm on the hunt for seats on my dads 482VS Commanche.

Wouldnt mind getting the cd

M.S. Caribe 1! Happy times.

Still listen to these guys CDs. I believe I was at this show in Missouri. Rarely missed seeing you all Lenny. So glad to see life is good !!

seems like their is a demand for "Parts and Labour" the cd the guys made when they were called Kindred Spirit ----I tried to contact them via facebook ,but got no reply. East of Eden is a great song!!

Saw them many times at the Longbranch. I had their cd when they changed their name to Kindred Spirit, When moving I lost it. Is there any way to get a copy? I loved Children Go and Geronimo!!!

i worked with tom & tony..would love to have copy of their album..can anyone help..martytitus14@gmail.com thanks

Lenny wallace is my dad. im will. please subscribe yall. he is really good still to this day.im very proud to call him my dad and again please subscribe and lik and even comment.

Remember seeing these guys at the White River Hoedown in Mtn. View back in the 80's. Worked with Lenny at the Stone County Leader too. So glad he made the change from the Newspaper to doing music full time. (Pam from the Leader office)

These guys were/are great! I wish they had got as successful as they deserved to be.