- 105
- 243 083
ARockyRanchShop
United States
เข้าร่วมเมื่อ 21 มิ.ย. 2013
A Rocky Ranch Shop
1950 Farmall Cub will it run 3
We are diving in deep into this 1950 Farmall Cub. This week we are tearing into the valves and cylinders. One step closer to getting this thing up and running. Thanks for for watching and following along as we get this old girl up and running.
มุมมอง: 177
วีดีโอ
1950 Farmall Cub will it run 2
มุมมอง 12214 วันที่ผ่านมา
We are back on the 1950 Farmall Cub. Fixing a little bit more and discovering more issues. Stick with me for this series and see if we can get this little tractor back in the garden.
1950 Farmall Cub will it run 1
มุมมอง 17721 วันที่ผ่านมา
Getting the old 1950 Farmall Cub out of the weeds and into the garden, hopefully!
Cub Cadet RT65 Tiller
มุมมอง 2625 หลายเดือนก่อน
It's spring time! Time to get the tiller ready. This tiller has a Honda GC 90 engine.
95 F250 Fuel Pumps
มุมมอง 806 หลายเดือนก่อน
Dads 95 F250 4X4 needed a little work. It's time for new fuel pump. one of the pumps went out 10 or so years ago and the other one seems to be getting a little weak. Don't want him to be left stranded so lets get them changed out.
The 96 F150 is going back together!
มุมมอง 557 หลายเดือนก่อน
We are finial going back together on the 96 F150!
2014 F150 CHT Sensor (P1289)
มุมมอง 1568 หลายเดือนก่อน
Getting the warning light "Engine Overtemp" even without starting the truck. Turns out there was a bad wire. Easy fix just hard to get to.
96 F150 Fuel Injector Pigtail Replacement
มุมมอง 528 หลายเดือนก่อน
Had some rodents chew up the wires to my injectors so I had to replace them.
96 F150 Rear End Swap
มุมมอง 678 หลายเดือนก่อน
When this truck was wrecked it was spun around and hit the curb with the driver wheel and bent the axel. So while we had the bed off to change the fuel pumps, I figured it was a good time to change the axel.
GENERAC PRESSURE WASHER
มุมมอง 298 หลายเดือนก่อน
This wasn't support to be a full video but it went to well.
F150 FUEL PUMPS
มุมมอง 749 หลายเดือนก่อน
Had to change both fuel pumps on the '96 F150. Found what seams to be a good deal on both pump on Amazon, We'll see how long they last. www.amazon.com/gp/css/order-history?ie=UTF8&ref_=nav_orders_first
96 F150 Bed Removal
มุมมอง 1039 หลายเดือนก่อน
Fuel pumps went out so it seemed like it was time to remove the bed since I have been putting it off. This is going to start a series of projects on this truck. I hope you stay tuned.
Single Click No Crank
มุมมอง 1089 หลายเดือนก่อน
When trying to start I get one click then lose all power.
Carb Cleaning and Steering Bushing
มุมมอง 639 หลายเดือนก่อน
Only had the new carb on the Fourtrax for a couple of months and already needs cleaning!
A very important aspect of headlight aiming is to aim them on HIGH beam, vertically straight ahead. Low beam should naturally aim a little down and right. Ya don't want to continuously flash on coming traffic on low beam when the rear of the vehicle hits bumps and goes up and down.
Well bud I hope you're all right I just watched your video I know it's been 10 months ago but hope you're okay but hey what are you doing with that red Ford pickup is it four-wheel drive or two-wheel and did you ever get that four wheeler running right if not I might be interested let me know brother in both of them keep up the good videos
The red truck is my sons, and we plan on rebuilding it. The four-wheeler is running, but rough just needs a little attention. They are the same year we want to restore both to keep as a pair.
I got the same color truck with the same lariat interior i love the green i thought it was black at first glance
Good job im doing 1 Monday 🫡
Great video ! Concise and easy to follow. Our JD 5055D had the same issues. Changing the prescreen totally resolved them. Tractor is running strong as ever again. Thanks !!
Would he have to program the new steering wheel column and key?
My pan has a support running across blocking two of the bolts is that supposed to be removed?
I haven't ran into that, I wouldn't know. What is yours on?
My wife's uncle gave us a cub cadet rt65 recently. He bought it new many years ago. It sat in his building for roughly 10 years. Both tires were flat and broke bead locks. It has a Briggs and Stratton engine. I put in inner tubes for the tires. Rather than fight with the carburetor I went ahead and ordered a cheap Chinese one from Amazon. Easy to find one, just need the numbers you can find on the carb. Spent less than $40 for tubes and carb and less than 30 minutes of work to have it running like new. Just a thought/suggestion about having to mess with the carb again if you need. Yeah i could have rebuilt it and cleaned it myself but for around $20 or so i got a new one along with a new air filter and spark plug. Was much quicker just pulling off the old one and throwing the new one on. I think the time it saved was worth more than the little i spent.
Those ramps you’re using look pretty sketchy. Good luck friend!
Thanks for this !!!
Will 97 crown Victoria rear end fit a 97 police interceptor crown Vic
I'm not able to answer that one. I only worked on this 2006.
You did a great job and give me confidence to do mine. Thank you
I only pump filtered diesel into all of my tractors (new ones too) and still had to pull the tank screen on my 5075E at 58 hours. Looked like it was fouled with dead diesel slime carcasses. I'm religious about using Killem algaecide to keep the slime in check. Danged if I do and danged if I don't. Problem with bio-diesel and low sulfur diesel: slime grows no matter what you do.
Thanks! Anyway to check one after you've pulled it out?
I think this is Mis- titled I should read why I need a new battery charger jumper. Haha I bearly had patience to try to watch parts of it. Change the alarm box instead of CDI by the way.
Why can’t you show what you’re doing?
Thanks for doing this video.
Saw you video on the Throttle cable. Replacement on the Land Master I have the Same one and have a question on Replacing the Foward Reverse Shift Cable. Have you change it?
Sorry, I haven't had to work on that yet.
16:22 but what is that tool :(
Nvm found it, it's in the descrip of the video "Easy out"
lol
The underpart of mine won’t come off is it just 2 bolts and some clips?
What is the part number of the sensor?
I found it. It is the cold start advance sensor AKA temperature switch. John Deere RE503242
@@mars1952 I could remember the part number. I believe I had to get it from the JD dealer.
Thanks for the tutorial, very informative and appreciated.
Thanks for making the video . Why is there terrible music playing louder than you are talking?
I have a 96 with the 5.0 and those spark plugs were absolutely the biggest pain in the rear end that I’ve ever dealt with. I don’t think we’re ever changed my mom and dad bought it in 96 they just gave it to me. Those were not fun at all.
I have a 5105 that I hope adjusting the PTO linkage will fix slightly slipping PTO. If not....$$$$$$$
I use this to program my keys but now it won't program the fob It just hunks some people say it could be because there's too many keys already programmed but I don't know how to get rid of the other keys I do have four scan though but can't figure that out either
Nice, the clutch Seems to work anyway!!!!
This is just too familiar. I had to fix a lot other things on mine!!!!!!
Very cool old tractors. Looking forward to seeing them come to life😎
So did you just pop it out and pop it in?
Pretty much, it was super easy. Wish I would have done it sooner.
@@ARR-SHOP Labor $175.00
It's easier to do the passenger side from the wheen well
MTF
You need to watch "Carburetor working animation" video on "biker labs" youtube channel. It shows how a normal throttle cable dirt bike carb works and how a diaphram carb, like the honda fourtrax 300 uses works. It really helps with trouble shooting a honda carb. Best video I found on honda carbs.
I am going throught the same thing. Trying to get my grandma's 1992 fourtrax running that has been abandoned outside in the tree rows for 6 years, without being started. I got it to run on starting fluid and cleaned the carburetor, but it still isn't getting fuel. It has the 2 main jets in the bowl. The taller one I can see through, but the shorter one I stuck a sewing pin in each end, but right in the middle it doesn't go through.
I finally broke down and bought a cheap Chinese card off of Amazon, and now it runs like a champ. You can check that video out on the channel. I really didn't want to replace the original, but I'm glad I did.
Don't forget to order a new choke cable for it.
What did the dentist do to fix your broken teeth? I broke off about a 1/4 of one of my front top teeth and have not gone to the dentist yet...
I dont know what he called it, but basically, he put a resin on it a little at a time cured it with uv light, then ground it down to shape the teeth. They look great and feel great.
I bet that starter was hotter than a two dollar pistol. I can’t believe he keeps trying, he is persistent. Lol
I have been pretty amazed that that starter just chuggs along and never gives in. Check out my newest video. I give it a good workout again. 😆 It stuck in there.
How do you adjust the pto clutch
I haven't had to do that on yet. Sorry, I can't help you out.
Thanks so much❤❤❤❤
YIKES ! That's a Lot of Work ! Great Job !
very cool
Explain why you wouldn't just remove it from the hinges first
Please right tight left loose
what size bolt holds on the wheel on a cub cadet tiller Its a RT65 Model # 21ab455c709 Thanks if you can help me.
Is this truly wireless starting without having to plug anything in? I wonder if this will work on my 2005 Tacoma?
Your not getting fuel
Wish your voice was as LOUD as the background music, no information/ show the parts! Explain what u are doing. Sucks
Do you have a part number for a new ignition housing by chance?
I need a diff