วีดีโอ

how do you start your 65cc? my clutch wont catch on the start thingy

Was the battery topped up with distilled water?i would recommend an AGM battery🤔🤞

Compatibile con Cromwell?

i have exactly the same problem, thank you for the video. is it possible to put a LED lightbul though?

et le vario

Good job

NIce :-) Merci

Adem

Hello sir. Thank you very much for the information you provided. Could you please let me know if there is a way to put shock absorbers on the rear wheel of the CIAO? Regards Spiros

Hello i need your help my pugeot fox key is gone and the steering wheel is blocked what do i do now pls need your help

Does Brixton Felsberg have a diagnostic connector to connect a plug and play gear indicator?

What about the spark plug sensor you didn't put it in the diagram?

Thanks alot for the video bro. How can we sync the idle revs. It keeps on increasing even withour the throtel. How to tune it for the rethymic sound and consistent revs. Thanks!!

Im assuming youre using a 13/13 deltoro what jet do you use in it

Hello!👋😃 This is Morten and I have been watching all of your videos about the Brixton 125 which are awsome!👌 But I wonder if you could help locating the 'intak air temperatur' sensor (IAT)? I am going to install a tuning unit on my Brixton BX 125 R (Sunray), but can not find the mentioned IAT-sensor which I need to connect this tuning unit to. Looking forward to hearing from you. Kind regards,☀

Bro can you disassembly the fuel tap to see how it works

Ik ben de 4 280 ste abonee

homeboy did a blackscope✨✨✨

The question is how are they after 20 -30 000km?

Ik ben nederlanden voor tomos hahah🎉

Hi! 👋😃 You really make nice videos! 👌 I wonder where I can locate the IAT (input air temperatur controller) connector on my Brixton BX 125 R? Thank you in advance! /Morten S. ☀

Where do you buy the top lock nut and lock plate you bend over top lock nut for the fork bearing/fitting?

Aint that gonna decrease The value of The vespa because you welded and cut in the frame? I’m just curious because I’m thinking about doing it myself

hello, how long is the tape needed? Thank you

Beste cilinder ooit ! Beter als die malossi rammel cilinders

ciao is not vespa

thanks man!

It's not wise to detach the switch while the kickstand is out (i.e. pushing against the switch). There is a force from the kickstand on the switch that pushes the switch along and therefore bends the 2 screws when they are coming loose. So the threads on the screws get spoiled. I also put short screws in the threaded hole finally, because the threads would be exposed to the elements at the bottom side of the bike. (And I always use al lot of multi-purpose grease in that areas. There are a lot of rusty Brixtons to be seen when you look out for them.)

Very good explanation. Thank you for sharing your experiencia. Have you drive it off road? In that case, how does it fell?

I have a problem with my peugeot fox. The backwheel can go way more than 36kmh when its on stand but when driven it only goes 36kmh and does not rev full out. sounds like a metal sound when it obstruct the bike. half throttle is the same. still metal sound but less rev and same speed. pls help

This is exactly what I needed. Thanks!

Tis " waar " niet " woer "

What battery is that, as I am looking to replace my default one.

I just changed my exhaust, but it is leaking a bit of black oil from where it attaches to the engine. when i plug it while running idle it doesn't stall. does this mean I have a leak?! Or is it normal

I have a 1996 ciao and it accelerates really poorly! What could be the thing causing this and how should i fix it?

thanks

How is the Brixton holding up after 5 years? Any rust or mechanical issues? I'm thinking of buying one myself. They now have an ABS version as well.

My daily hobby……!

Ik heb momenteel exact dezelfde problemen….. en dat terwijl ik al meer dan 7 jaar bezig met Citta’s en er een pakhuis vol van heb. Zeer helder filmpje! Thanks! Elke dag leer je weer….!

I use special wax for my motorcycle helmet visor and it works great! 😊

Do you have any idea if a variator is bolt on installation or you need to change any shafts for that?

Geiles Video. In unserem Kaff haben wir Gläser mit Griffen bei der Kirmes also musste ich ein bisschen improvisieren bei meinem Meter. Hat aber trotzdem gut geklappt.

Dikke brommer heb er ook een gekocht 👍👊

*The chewb*

Is it possible to buy a cylinder kit where you dont have to drill to match the Ports?

Same problem to mine.thank You man

Could you use copper ease as the grease?

Telenet duurste bucht

The 125cc engine comes from a suzuki so if you can find a service manual for it everything should be the same

Avrei fasciato di nero anche la marmitta e lasciato il cupolino, ma i gusti sono personali. Bravo, ottimo lavoro, pulito ed efficiente.