วีดีโอ

@@DuaneDonaldson it's built into the max what you got to buy is the t Ninja box separate but I use the launch Xprog 3 cuz that was the first one.

@@markdasparkauto1780 do you know if the OBDSTAR will work like these others? Cheers.

@@johntran9131 you could go on Google and download Smart pro immobilizer instructions it will have a list with all the cars and different versions

The only programming you might have to do is a gear selection learn

@@mhorton901 it's a clip to read the data on the frm module instead of soldering wires if you are doing that job that's the best thing to get

@@markdasparkauto1780 can you provide a link as I am I'm only able to find it for the vvdi not the xp400

@@mhorton901 www.ebay.com/itm/225928787247

@@mhorton901 just Google BMW FM module clip and you will see the clip on eBay

@@IddrisuMubarak-kq7xj you do not have to buy the max they got cheaper version of this

@@josephkebbi1146 you are welcome anytime bro

@@itssKayla2000 got to pull the front covers off put new timing chain guides and tensioner good to go

@@fritzs1207 is the ism virginized

@@tresorkimbili6370 no problem my brother I will start to make my videos of all the connections from the start to the end

To me when it's writing or copying a flash or a full data backup it always pause then start back writing I use this tool for a couple of years and that's how it worked and thank you.

Thanks for letting me know, regards

@@joelcruz-kq5cu you got to go into special function and look for VIN number

Yes you can put the resistor between high and low but it's much easier with the adapter.

@@markdasparkauto1780 So your adapter already has a 120 ohm resistor?

@@markdasparkauto1780 Did you download the firmware and coding from the old TCU?

@@serobmanucharyan3554 yes I did I had the file saved before. so all I do is renew and write the file into it

@@markdasparkauto1780 friend, another question for you, if the non-working board is 722.9 V2, and I install the donor 722.9 V3. Will V3 work with the old firmware V2?

I believe after 2016 that was it 2016 envelope you are good

@@markdasparkauto1780 what do you mean by envelope ? Can’t find my model so can’t read it

@@GhaithAlshaary after 2016 no way only dealer

Yes sir

@@kennardhaywood7100 yes just do PCM replacement and forward the steps

I have been reading that I must also replace the immobilizer with the one the used ecu comes from. Is that true?

@@kennardhaywood7100 no

Thank you for all of your assistance.

@@kennardhaywood7100 you're welcome

@@kiddynamite2785 Autel ultra

I'm in New York Brooklyn New York

I don't think it is supported yet.

@@markdasparkauto1780i mean not used tcu from 2007 cars?!)

You are welcome

Year

2016 car is running normal but i need to change vin only, do you have fb or whatsappž

I never did 2016 Nissan VIN change yet but I did a 11 a few days ago probably need a programmer to do that on bench.

You are welcome

No problem

When you hook it up does it communicate

@@markdasparkauto1780 yes it does and reads all details , but when I try to erase it says failed to erase please retry

You got to check your can bus wires the 6 and the 9 could be confusing so switch it around and see

@@markdasparkauto1780 I inter changed them and still thesame , on my wire the 9 has a little dash sign under it , so basically I did it right

@@markdasparkauto1780 please help me out, I really appreciate

@@markdasparkauto1780 hello, please your response will be much appreciated

@@kva_powerup Hi, did you solve the problem with the IMMO plus and the VGS3NAG2 plate?

Yes it could depending on what year

Autel elite

No that call is not on the list.

Thank you 👍

No I don't have any files.

Is that car gas or diesel we do not have that car name here in the USA. start with engine size.

You are welcome my friend.

​@@markdasparkauto1780 i open the front timing cover an hour ago, and fuck sick! You're right the engine is out of timing! Need to change the timing chain set.. i almost replace the ecu...thank you soo much.