- 55
- 36 650
M. B.
เข้าร่วมเมื่อ 20 มิ.ย. 2014
วีดีโอ
Setting winter Studer 2x XTM
มุมมอง 6202 ปีที่แล้ว
seting system Studer , low consuption XTM, grid peak help,
input limit paralel XTM 4000 Studer Innotec
มุมมอง 6943 ปีที่แล้ว
Studer XTM 4000 -2x paralel - input limit !
Can u please tell me how did the Inverter came from standby mode to ON mode ??
automatically, after increasing consumption, the inverter switches to ON mode.
it is also possible to turn off the foot standby function with parameter 1500.
Is this a good inverter so far? Studer!
Yes, I can only recommend. There is probably nothing better on the market with lower self-consumption for off-grid installations.
Did you find that they were much brighter?
No, only 10%.
@@m.b.2255 Thanks for that
Hello, could you please help me I am getting 7-Ac-in too low error So inverter not charging from grid sometimes
Xtender par. 1199 , 1200 ?
Jjj,pekne,co tak skusit to zdvojnasobit ? :🤔😉
zdvojnásobit zátěž ? To by šlo , jen jak bude trochu více svítit 🙂. Zatím je sluníčka málo . Napodoboval jsem test distribuční společnosti a ta spínala první pokus 1,5kW odběr a druhý pokus nominální výkon měničů a rozdíl v tom v podstatě nebyl. Studer testován nebyl , tak jsem to musel zkusit 🙂.
@@m.b.2255 Ok,pomalu konci doba temna🙂
@@lugemont u nás opravdu pomalu 🙂
photos.app.goo.gl/yoQybEdS8QCdbztL7
what batterie you tested ?, it's surprising to see 60 volts and discharging to more than 40 A. Very interesting to learn about studer inverters.
Hi, the battery has not been tested. The battery in the installation is from a Nissan Leaf 16s. The test was whether there would be an unsolicited supply of energy to the electrical network, in the case of a switched load of 2.3 kW for 4 seconds ON and 2 seconds OFF for 30 minutes. The result is 0W according to the 4Q electricity meter of the distribution. 🙂
Whats the password for advanced user ???
different levels - different codes, password Expert :426468
I frequently have problems with both the Android app and a PC using a browser not being able to pull data from the Studer cloud. All the icons turn gray, and no values appear. I have tried a different service provider, and still get the same results. Have you seen this problem before?
Dobrý den, jaké prosím máte baterie, a používáte BSP500 ? Děkuji
Používám baterii z Nissanu Leaf a používám i BSP500 ano.
witam, możesz mi powiedzieć czy pilot rcc-03 będzie pracował z inverter studer 1400-12 XPC , mało informacji w polsce
www.studer-innotec.com/en/accessoires/compact-series/rcc-01-remote-control-1061
dla XPC będzie to RCC01
www.studer-innotec.com/media/document/0/manuel-xpc-en_v6.02.pdf
@@m.b.2255 dziękuję za odpowiedz, pozdrawiam
La como hago para iniciar sección me puedes ayudar
www.studer-innotec.com/en/downloads/
Xcom-LAN Quick guide
@@m.b.2255 Si pero el sistema no cuenta con esa función ya que en el lugar donde se encuentra instalado no hay señal
@@juancamilolopez3874 ¿Ni siquiera es GSM?
@@m.b.2255 Siii esa función si la tiene pero como te digo no contamos con señal telefónica
Dá sa tam nastaviť horná hranica nabíjacieho napätia napr. pri 15 článkových batériách ?
Ano, je možné nastavit hodnotu nabíjecího napětí od 37,9V do 68,2V.
@@m.b.2255 Super paráda ďakujem a prajem pekný deň.
Je možné nastavit jak hranici podpětí od 34V , tak horní hranici přepětí do 68,2V. Zárověn hranice návratu z těchto krytických hodnot. Je toho hodně. viz odstavec: 1.11 VarioString parameters portal.studer-innotec.com/Content/docs/appendix.pdf
I would like to ask if is possible to user this inverter with no Studer brand MPPT controller, for example Epever or Victron. Thanks
Yes, but they wiill not comunicate to gether . But that's not a problem.
I like STUDER inverter
Why that 3ed phase is open ?
I'm so sorry. The comment belonged to another video. Here it is really like three-phase connections. :-) but only with two inverters. The third phase is free because I only use 2 XTM 4000. I don't have any 3-phase appliances at home.
Here was an example of the behavior of the inverters after reaching the set value of battery discharge. The consumption of the house was taken over by a public grid.
If you have 3phase load connection what should you do?
@@jibindavis2143 use three pieces of inverters (for example XTM) and parameter 1283 to Yes 1461 -Yes 1462 - No
Thank you sir
Hi. Do you know what error code 163 and138 means. Thanks
como puedo restablecerlo a estado de fabrica
par. 1287
no me aparace battery monitor
hola en mi panel no salen esos valores,tendre man conectado los puertos
estoy tratando de configurar el mio,existe algun manual para hacerlo
th-cam.com/video/hsxRWlHTWfI/w-d-xo.html Por favor, la guía no es solo inspiración.
www.studer-innotec.com/es/pages/soporte-tecnico-7230
Hi sir could you please explain how to resolve error?
Aby more information?
If you don't mind send your whatsapp number or other social media network id
@@jibindavis2143 please use email: milhavti@seznam.cz Tank you
Nice explanations, Great job! All the best,
ok I have a real question. lets see what the flipper knows! the Bothe the XTH and XTM models make 230 single phase power for the consumer. but you can also program them to 120 @ 60 Hz consumer power. Can you program the AC in to accept 120 60 Hz at 30 amps generator power for charging of batteries?
No problem .
what a useless video! my goodness I can flip thru all that like an idiot myself.lol why watch another idiot do it!
Thank you for your inspiration.
I just gota XTM 4000 - 48 and a XTH 8000 -48. I have done alot of reading to get the entire PV panels to charge controller. charge controller to batteries. bateries to these two inverter chargers... success! but now im stuck because my electrician doe not under stand how to get the power from the two units to the traditional panel with breakers. quiet frankly I am confused to. as I donot understand how either. After watching several video's on 120/240 power panels and how the power comes in from a grid. There are two HOT wires and one nuetral. but nither of my inverters supply 2 hot wires? just one Live and one nuetral? both models claim 230 volts. but only one hot and one nuetral? I bought the XTH 8000 - 48 for a 230 service ability to run deep water well pumps... I think whats happening is one XTH 8000 only supplys one leg of the two legs needed for 230 power. I need to buy another XTH 8000 -48 and link them together for two legs... I remember Victron energy having a simular system when Iooked at them. Im just not sure. there is a Phase selt jumper switch label'd #10 in the fangpusun handbook. I havent determined what role that plays on power output but I stll only have 1 hot wire to the panel . . . any information would be appreciated
I'm sorry, I just don't understand what the question is?
www.studer-innotec.com/en/functions/xtender-series/?id=4842
@@m.b.2255 Can I do AC coupling in the US with this inverter (120 -240) since it's rated 230?
@@DrairoOrtiz Get the 120V/60Hz version. Available.
Hello my friend,very good solar energy harvest. 👍
1:43 Is the Smart Boost % limit can be changed only in Expert settings?..By the way thanks for uploading this video.
no, only in the installer settings. you're welcome... video please only example, each installation is individual.
@@m.b.2255 so you got installer password to change the Smart Boost Setting? I think the default or factory Value is set 100% but you set it at 80%..
@@ricky786 Yes. I did not change the setting of parameter 1607. according to RCC Quick guide yes 100%, maybe in the given Xtender System Update that I use, it has been modified.
@@m.b.2255 Oh, that's strange..What inverter software version do you have?
@@ricky786 I have R 644 and I have 80% friend has R652 and is 100% strange...
So, you can charge your battery directly from the gasoline motor while parked? Interesting.
It is not directly designed for this. The Prius Plug in can be depressed on site - depressing the brake pedal and at the same time the accelerator and battery will be partially charged.
What is the % step of standby mode setting adjustement?
0,10,20,30....100%
@@m.b.2255 thank you for responding...Can you please check for me also the current step for grid feeding function ?
@@ricky786 ...........0,19- 0,39-0,59-0,8-1A.... to max imput limit . for example 25A. step 0,2 A.
@@m.b.2255 appreciate your response..🙏
Another question, if the grid feeding is set as "ON" but the grid feeding current is set to "0" zero, what will happen to the power outputs?..
je dispose d'un BSP, un XCOM-232i et d'un RCC-02 mais je ne parviens pas à le faire fonctionner. j'ai vraiment besoin de votre aide je vous en pris. j'attends votre réponse. merci bien
Bonjour, s'il vous plais j'aimerais savoir comment mettre en marche le STUDER INNOTEC RCC-02
Lorsqu'il est connecté à XTM ou XTH, le RCC démarre automatiquement ... Quel est ton problème?
mon problème est le suivant: le BSP est connecté à une source de tension 48v (en continue) puis le XCOM-232i est connecté au BSP via un câble RJ45 et le RCC lui à son tour est connecté au XCOM-232i aussi par un RJ45 et aussi à un moniteur solaire par un CAB-232-STUDER. le BSP lui démarre sans problème mais le XCOM et le RCC ne démarrent pas. je ne sais donc pas si il quelque chose de manquant dans le système ou si le problème est ailleurs. merci encore pour votre aide.
@@robintadem598 votre système ne dispose pas d'un convertisseur de tension XTM?
@@robintadem598 Il est important de vérifier l'ordre de câblage et l'état des commutateurs 0-1 à côté des câbles de connexion. selon le manuel. le logiciel doit également être unifié dans tous les appareils.
@@m.b.2255 Non il ne dispose pas d'un convertisseur de tension XTM. il ne contient que les trois éléments cités plus haut. merci
its needed 2 inverters for the hybrid mode?
No. Enter is AC in. Exit AC+inverter = hybrid mode .
0.29 x 52.5v is 15w. Why did it say 24w?
Dík za info.
supeeeeeeeeer STUDERPRIUS
Hezky sestříhaný
Bomba
Super video a tvorba like👍
Super
Krásné videa like odběr. Damián od Marka Brokeše 😉
Jo ty
Ňak nemůžeš ne...? 😂
Martin Basler ..... já ? 😉
Dobří😎
HI. What is the ADc reading? does it show battery capacity in AH? and what is the KW reading in the L1-1 screen?
Please email, send photo....
dobrý☺☺
dost dobrý ☺
Mareček Brokeš
ff