วีดีโอ

Finally a great video showing the actual make/model of an actual F10 535i, or 3.0L MAFS location and replacement. Great video thanks!

I'm looking for a little help. Will this fix code p12A9 boost pressure too high?

What code did u have for that specific sensor ?

Thank you very much for this video! Very helpful. Changed out the MAF today in less than 25 minutes!

I put 15psi, leave it there for 10min and holds all the pressure. But then i find coollant spills in the engine bay. Any ideas??

Awesome video bro keep it up

So is that a bad sound ?

Great video and easy to understand. Do you have the part number for the heating/vibro control module?

Does the 5 series and the 7 series have the same exterior door handles??

Thank you for the video. Anyone know if the sensor can be cleaned? Using the MAF cleaner?

Sir I’m about to customize mine you don’t know how much I love you I just need to learn how to take the dash apart thank you

Comfort entry doesn’t work for me with the after market handles

I did a first oil change on my 2011 and i had to take the skid plate off...only had 2 bolts in the front and 2 in the back. Going to replace them all do you happen to know the screw size for those 6 in the front?

Good video. I wish my engine was that clean. I'm going to work on that.

this music is hilarious

Damn I needed this video! Thank you do much🙏🏾

Where is sport button?😢

This the same for 2008 535i e60?

You took a lot off the 535igt i just reached straight down 7 mins done...

I just brought one you do you no about the seats

If my BMW dont have comfort access handles, can i upgrade it and how. Can i just buy comfort access handles or it must have some moduls to put in door? Nice regards.

Thanks man!🤘🏼😎

Do you put it over the old one or do you take the old one out ?

I've seen 100s of how to videos on youtube, your is easily the best 😍 Thank you

Hello. First I want to say that you made good job. You’re the only one who made a video manual of retrofitting. I’m about to do the same thing in my f11 but I have question. My F has lane dep. warning, light assist, but doesn’t have acc. Do I need to buy a steering wheel with heat panels and button? Ofc I know about coding. But i red on some forum that I will need to connect one wire behind passenger glovebox. Is that true? Appreciate for help

Need assistance- so on my 2015 bmw x1 xdrive35i E84 won't stop bleeding usually stops around 10 to 15 minutes but recently it won't stop - is there anyone that can asset?

Don't have BMW (yet), and part of it is that I can't find a spec I want, but your vid brought ease on my mind - looks like pretty easy swap! Subscribed.

how are you removing the huge bolt connected to the hose

❤ ->>> I have a XLH 1200 1998 -> I don’t like the bigs - I ride only on my towm 😂

❤

❤

Simple and great video to the point, thank you and btw great sponsors :)

Hello, I have N57 3.0D I follow this instructions however pump isn’t starting. Does anyone have idea why?

I wanna leave mine out for winter how do you remove without alarm going off ? Cheers

Yo no encuentro ese sensor en mi bmw 528i 2012

Thanks for the Video! What kind of oil pan is this and where can I get it?

👍👍👍👍👍

This video helped a lot, however, the screw size is a T6 and not a T7.

What is the size of the piston and seal?

I love you for this video man

Thanks alot. Just saved €1000

This might help those that can't seem to get the bleeding sequence to start. I don't know about other BMW models, but on my 2012 535xi, when you floor the gas pedal and THEN if you push harder you'll feel a switch being engaged. That's what I did to get mine to work. The pump is quiet and so it helps if you have someone outside under the hood listening for the pump when it comes on. Also, stay in thee car until the 10 minutes or so is up. It seemed in my case, when I opened the door to get out it MAY have canceled, but I don't know for sure.

Great video. Easy to follow and insane organization. Thank you for posting!!

Thank you for the great video, but it doesn't work for me. My vehicle is bmw 520 xdrive N47D20C diesel 2.0 184 ps. I wonder why it doesn't happen?

What year?

Do both solenoids need replaced and are they both the same exact part?

Hi Brother, I have noisy coolant ventilation when AC is on, As I read from internet, there are 2 reason, one of the reason is : coolant system that's filled with air pockets and hasn't been bled properly. Could you please help me how to bleed it?

I saw another video they used a computer to activate the throttle this way the throttle can be open while they do the test you didn’t do that but the test came out fine.

Your videos are really awesome and very good quality very nice I really enjoy watching your videos. But there is a little problem with your video, you should do SEO, if you do SEO, your video views and engagement will increase, likes, comments, and subscriptions will increase gradually. If you have less idea about this, you can tell me and I will help you.

I legit been looking for everything your doing online for my Aspen. Your a god send! Also subscribing