วีดีโอ

I’m a girl that’s about to do this herself. Wish me luck! Do I need to reset the computer? Disconnect the battery or will the sensor just reset it self after I change it?

I wish people would actually show the 2007 models on these videos. The 07 is totally different. Smae position, but above and behind the exhaust, and you have to go in thru the inner fender. And, a wrench won't go on You HAVE to use a ratchet.

Looks like you’re too hot for this podcast 🔥😆✌️

You forgot to install the front bump stop which is no good!

I need a new blower fan and a new cabin filter while im doing this! Thanks for the lessons!

Straight to the point. Just for me though I don't think you need to struggle with one hand to demonstrate whole removal. Just start it and show it removed is plenty imo. Appreciate the video!!

Take off drive shaft. Remove seal. Install seal. Got it.... Terrible video man.

Did you also have a p0300 code too? Mine just came on today and had both P0339/p0300 I replaced the sensor and reset the codes so far so good

Useless

Is it necessary to fill the speaker box or will it be fine without being filled?

Torque? Tools used?

Jeep Liberty 2004 and mine is welded in apparently with rust? Won't come out for anything. The screw unscrews but can do nothing from there :(

I know this fix at least two to three years old but is there two of these camshaft sensors on JK/JKU 3.6L ?

Great video, Was this on a stock Jeep? I have a 2018 stock Sahara and want to add some quick release sway bar links.

my 2014 start doing it stalling at 245km when it want thanks for the info time to change it 👍🏻🔥

My 2014 Wrangler JKU Rubicon just threw this code when I started it up last week.... P0335. I only have 58k miles on mine.

Wondering if that would be the cause of a P0340 or the p0018 that just happened

Will it work with the 5 speed manual transmission?

I got about 169K on my 2013, i’ve never replaced this, but when I’m accelerating, sometimes I feel a little bit of a power drain, but then it kicks back up the further i press the pedal, not all the time though. could this be causing my problem as well?

Is this liner a hard plastic or is it rubbery when you touch it?

Wonder why they don't offer rear side panels for the LJ Kind of an incomplete package without them?

not a smart tool

So, did you have to lift the lock tab on the connector or squeeze it? This is a great video! Thanks for getting in there with the camera.

There was a KK there last year also. We're going again this year

You didn’t show how it came out. This video is useless.

My 2014 JKU had the idle just drop to zero while driving on the highway. Still had power but nothing even when downshifting (6 speed manual). I was able to just turn it off and back on and had normal idle again. I’ve had CEL on for wheel sensor and crankshaft position (PO018) that comes on randomly. I’ll see how it drives tonight when I get out of work. Hoping the fix suggested in this video might solve it if it happens again.

Thanks man. This happened to me this morning. Once I had the part I was back on the road in less than 10 minutes.

You’re using that jeep I see mud

Looks good Billy 🤘

🥶 Nice Work! 💪💪💪

These things make a huge difference! 👍

Man that’s gotta stop all that feet roasting heat!! Awesome video man!!

So, how is it?

Great video. Our 2012 lost power and was throwing up codes like gang signs

Great video. Our 2012 lost power and was throwing up codes like gang signs

Thanks for this!! My JKU is a 2013 and it just went out at 83k miles. Thanks for the clear and simple video. Happy Trails!!

Should you disconnect the battery first?

I call mine B.O.B. ( Betty Of Bolts )...Got duck #5 good to report. Looking forward to my N3 suspension upgrade. Safe Travels & Trails.

Say Jeep Life Podcast I enjoy your shows for sure. New to Jeeps. Wanted to share Jeep Wrangler Team wheeling in Japan I think. You may or may not have seen it here on the tube. Just wanted to share seeing other Jeeps in other countries. Safe wheeling.

Any advice for the Deathwobble in my 2012 Jeep Wrangler?? I'm new to Jeeps 3 year owner & only 1 trail. Learning. Thanks.

Listening to The Jeep Life Podcast for the first time. New to Jeeps (Virginia). 🚙. Thanks for sharing your thoughts!!

I just replace mine today. Thank you very much!

One of the most cursed phrases you'll ever hear while working on your Jeep is..."It or they should come off real easy"! This refers to screws,doors,hinges,soft tops,hard tops,bolts,bushings...etc,etc...!

I just replaced mine with plastic bushings today hopefully this will solve the door seizing bullshit that the wranglers are known for 😡

What's with the yelling, used-car salesman voice that every youtuber uses?

Not too shabby! Putting that new welder to use!

Nice! What's our first bending project going to be??

Nice job!

Wish i could get one but they dont ship to Alaska 😢 they look like great machines.

…I always eat the silica gel