วีดีโอ

um

Jessie is much prettier than Wade Lalone.

Amazing detailed video!!.🏆

I have a 1999 F-550 do you know if a 2005 F-550 rear end will bolt up into the 1999 ?

I drove the counter shaft race in flush with inside of bell like in the video. Installed 2 shimms and dropped in the spacer i still have almost a 1/4 " left to shim for spacer to be close to flush with input shaft retainer. Do i need to drive the race in deeper?

Does this work on the updated seal?

How do i know my clutch is messed up and not synchronizers

When opening the oil passage. Why is only one opened and the others cleaned of the flashing?

nobody ever covers detailed inspection of shift collar wear or points on syncros

How different is a 1965 Dana 44 from this one?

Do you have anything on a 2018 4500 ram front axel input seal?

Need price

With these and other ford superduty parts going possibly (dont know the real numbers, just know many already are) obsolete any plans to make some of the superduty parts yourselves ???

Do yall sell the tools for installing the hub seal on the axle and installing in the knuckle and doing inner oil seals

I am looking for a divorced kit for a NV242. Let me know if you can help please.

This is the best video I’ve seen on replacing these, the TS3065 made it look easy.

He said a small hammer. Proceeds to pull out the largest dead blow ive ever seen.

Do the 1356s have crush sleeves that need to be set when putting them back together? I'm currently pulling mine to replace the inner seal and resealing it for leakes. Thanks for sharing this video.

I did not see a dial indicator used to measure backlash

Why are you installing a new ring gear on the Differential Carrier with what appears to be a broken off bearing boss?

Awesome!! Thanks for the video.

Thank you! Good video

Can I send a 4×4 core for a 2wd rebuild

If you’ve went this far and didn’t take off the adapter plate to reseal the cam o ring in the 24 valves, you’re gonna learn the hard way 😅

AWSOME MAN GOTTA LOVE THE USA, makes you wonder why snap on and otc has/had a hard time engraving USA on their tools. how long does a tip last ?

I'm tearing into one now, the front gears on the main and countershaft are completely stripped and input shaft bearing .Got to fix it cheap and good.was working and was stolen by teen that said it just locked up and quit at 15 miles.

Can anyone recommend a place around Montgomery Al to get my NV4500 swapped and or rebuilt? It's n a 1992 D250.

What is the u shaped tool, soory been drinkin a lil here, that a presses against the yoke ?

What is the GD brand of that C-FRAME press ? and where do you get one of those bohemoth MFs ???

Where is torque king located, do you have a store ?

like your products, is quad 4x4 (maker of this installer) your company ? it says usa made and where is it made?

What is the approximate torque to start crushing a new pinion crush sleeve?

Rare emergency brake assembly

Why don’t you just sit it on the floor ? 😂

i did my u-joints without renoving axle shafts while doung ball joints, easy pease, even for a 64 year old retired diesel mechanic with a 03 3rd gen sitting on driveway,

Do the scout ll and terra have the same axels? Meaning they can be used on either? Thanks

Is it possible to get the 3rd member to tight? I adjusted my bearing preload with that tiny tool and it took some pretty good leverage with my ratchet. Is it supposed to be that tight? I mean i did check overall pinion inch lbs after i finished and im sitting at 40inch pounds total from the pinion and 3rd member preload. I just dont want that 3rd member to tight. Might overheat if i got the preload on the third member to tight right?

Is the big gear supposed to be all gritty spinning it freely? It goes away moving the shift collar… but I don’t remember it being all crunchy spinning freely 🫤

Where was the torque calculation since the tool added leverage to the torque wrench? Why not put the torque wrench on the tail shaft so that it is on center? Amateurs.

They make punches for roll pins. Less chance of screwing them up.

Way overboard on the sealant. I would never beat on a syncro hub with a metal pipe like that. Learn how to use heat and freezing. That stuff will fall on. It's called finesse.

Great video! Thanks!

So many good one liners in a such a short clip. And helpful thanks!

Can a 94 ford dana 60 be retrofit to a 98 on up dana 60? Im looking to put the full hub assembly from the ball joint to hub

Can you retrofit a 95 dana 60 hub on 1998 on up axle?

What is torque for bolts to tight these bearings?

Great videos! Building my second NV5600. Why cant you leave all the shift rails out and input seal when checking end play?? I remember my last one. Its an act of god getting them all lines up.

Says front axle service in title why are you showing back rear?

Never heard anyone call the outer baring race "cups", but I'm not saying it isn't a proper term either. I assumed the "cups" are what the outer bearing races went into? Also, what was the reasoning behind swapping out the tone ring? I couldn't see damage to it?