วีดีโอ

I just read, ‘freeshipping’ worldwide, WOW

Muy interesante, how much it costs to ship within Europe?

i love your videos man, you are so amazing

Very well done my friend.

It looks very good, does it come with Abloy tips & tensioners?

Wonderful!!! I have already ordered one!! 😃👍👏🐾🐈‍⬛👏

Thank you for watching! If you'd like to purchase one, they are available here, free shipping all around the world! opsasec.com/discombobulator/

ola, sou do Brazil. poderia disponibilizar o diagrama da ligacao do Arduinno

Where can I get these? :)

Hi! I have a Berger Lahr Model VRDM 3913 LNB & VRDM 366/50 LNB Servos. But I don't have a good knowledge of how to operate these and also how to identify wires. Could you pls help me to give it a start. I have a fair knowledge of Servo Motors and Arduino. But have no access to relevent literature re. Subject matter. Kindly be good enough to direct on setting up the same. Gerald

Hand is in the way

The sweep command certainly works. I'm wondering if the sheetmetal function will be able to manage this so that it will give a flat pattern in the end.

i am trying to use : Raspberry Pi 4b or Auduino Delta Touch Screen (DOP-110WS) Panasonic Minas Driver (MADLN05NE) Panasonic Servo Motor (MHMF092L1U2M) Can you provide some support on this project? We had posted this project in a few freelancer website but could not get a suitable freelancer.

Need to post a photo of the final product!

Good job please can i have the code and diagram?

I would like to deal with each other, communicate and communicate

Hello, In the video, the program 48 of the servo driver is set at 1000. When set with the tone function tone(pin13, 10*1000, 1000), the servo motor do complete turn in one second. Does it means that if the program 48 was set at 500, the servo motor would turn twice in one second? Thank you.

Are you using encoder feedback to the mesa card? If not, does the drive jave a tuning function?

Hi , can you give us the Arduino code for test? Thank you ❤

this will probably sound stupid but why does the motor constantly spin if you wired it to position mode? Shouldnt that be speed mode?

A wiring diagam and code would grately appreciated..

you're just showing your hand!

Thanks for this tutorial. It was really useful. I bought the same servo motor and driver and in 15min, I was able to control it. Have you ever tried to control this servo motor by position? E.g. go to 20 degrees or go back to intial position. I guess you would need to get position feedback from the encoder. Do you thik this would be possible with an arduino? Thanks in advance.

I was on the lockpicking discord looking for disk picks and they spoke of the discombobulator, but also, a higher end pick thats also made by Tarehjerne. Is this true?

it's very useful.

Great job, man!

Hello everyone, i would like to hear your opinion about somethimg. i am concerned about design of abloy protec 2's sidebar. I own 358 and when i checked the core i noticed that sidebar is very thin. Also, 90% of sidrbar wasnt even spported by solid brass. Mostly disk spacers were holding it in place. After couple years of rusting, already thin sidebar may additionaly deteriate and weaken. I am afraid that this (in my opinion) weak design makes it suspectible to torquing-the-core attack (someone could put flathead scrwdiver bit in wrench and start torquing the lock until it or bit brakes). I am really concerned and would really appreciate hearing your opinions. Thank you for your time. P.S. sorry for grammar, i am not native speaker.

Theoretically, what you are doing is possible, but the minimum you need to know about this padlock is the CODE of the key.. if you don't know it and you don't know the angles of the discs - it's a total failure! Time, time, time, passes.. You can tickle this padlock long and well! Yes, let's not forget that despite all this, the padlock is easier to open than the euro cylinder). Abloy knows what he's doing!

Hi,my name is Million Haile.can you show me a programm and wiring of arduino to servo to control for bar soap cutting machine with adding induction prox.sensor and encoder?Regards Million Haile

Remember me a little to a Fichet 787 french Lock. This Rosengrens Lock looks very secure

Wonderful job. Please share the code and the wiring diagram if possible.

Could you please share the PDF of this drive

"Exactly what I was looking for! Thank you. I ordered a Lichuan servo a few months ago, thinking it would be as straightforward as any other stepper motor with step and direction pins connected to an Arduino. Could you please assist me in figuring out how to make it move? Is it possible to get your email? It would be very helpful."

Followup video: th-cam.com/video/W1lqBNQX9AY/w-d-xo.htmlsi=B4W97bDyDWf65oFX

Thnx man, it's very helpfull :)

Is this PWM pin connecting to arduino pin?

Did you set any parameters or setup in the motor before running the code?

Hello, what AC servo did you use for this project? I'm planning to build a boom barrier this upcoming summer. It would be a great if you have any suggestions :)

I did this ❤ th-cam.com/video/aFmfpvh9wdo/w-d-xo.html

Im having troubles identifing the right configuratiin of wire😅. Can you share the wire diagram especially on the connection of the input output connector

Hoping to know what pins did you use in your driver coder since I have 50 pins and don't know what pins should I use in my Arduino Uno. Thank you❤

Hello folks, somehow this video got a lot more traction than it should. In 3 days from aug 9 there will be a wiring diagram here: I do read comments!

Can I get a wiring diagram?

Hello, please give me the code and wiring diagram

Any chance I can purchase the rear tensioner pick off your goodself

Hello,is possibility send or sell for me wiring diagram and Arduino code!

Hello,is possible send or sell wiring diagram and Arduino code?