- 18
- 27 226
Clay Autery
เข้าร่วมเมื่อ 7 พ.ค. 2008
2007 RAM 3500 Suspension -The Saga Continues!
Just a short update. Life gets in the way.
Here is the fastener information that I mentioned in-video:
Lower Control Arm (LCA):
15/16" bolt head. 15/16" nut; 1-1/4" deep 6-point socket or box end wrench for fixed cam nut.
Upper Control Arm (UCA):
21 mm short 6-point for the nuts
1-1/8" open end wrench for backup if special carriage-type bolt cams out.
Spring Compresses Length to be free on LCA rotation down:
10-1/4" or 125 mm rod on the free side of the nut.
Spring Tool: 1-1/4" wrench or pass-through ratchet/socket.
Here is the fastener information that I mentioned in-video:
Lower Control Arm (LCA):
15/16" bolt head. 15/16" nut; 1-1/4" deep 6-point socket or box end wrench for fixed cam nut.
Upper Control Arm (UCA):
21 mm short 6-point for the nuts
1-1/8" open end wrench for backup if special carriage-type bolt cams out.
Spring Compresses Length to be free on LCA rotation down:
10-1/4" or 125 mm rod on the free side of the nut.
Spring Tool: 1-1/4" wrench or pass-through ratchet/socket.
มุมมอง: 28
วีดีโอ
Cesar Guerini Magnus Sporting 34"
มุมมอง 932 หลายเดือนก่อน
Nicest firearm I have ever owned. It is a murderer of clays, but would be equally dangerous to pretty much anything flying.
Ostomy Barrier - Trim to Fit Procedure
มุมมอง 2142 หลายเดือนก่อน
If you are, or are supporting, an ostomy patient, then we hope that this video, that illustrates how I trim the barrier base as part of our overall application procedure, will be a blessing and a use for you. My darling bride's colostomy is quite challenging in several respects. This procedure is what we have settled on to: 1) Minimize chances of leakage of waste material into a place where it ...
More 2007 Dodge RAM 3500 Steering and Suspension
มุมมอง 584 หลายเดือนก่อน
This part of my day was spent working on the 1-ton.
30 Days of Summer (part 2)
มุมมอง 154 หลายเดือนก่อน
Part 2 of what I chose to video and then throw together in a pile for you all. Feel free to ask questions. Hope you find something of benefit to you or at least mildly amusing.
Tips & Tricks #3: Clean Your Used Hardware.
มุมมอง 254 หลายเดือนก่อน
If you choose to reuse hardware, even temporarily, it's just "horse sense" as W.J. Harlan told us, to clean it up. Especially if you care about a proper torque reading on installation.
Tips & Tricks #2: Reusing Hardware? Maybe.
มุมมอง 264 หลายเดือนก่อน
As always, the answer to the question: "Can you reuse hardware?" is... "It depends." But if you are going to reuse hardware temporarily (like me here) or as a matter of course, then this video may help you out.
30 Days of Summer (part 1)
มุมมอง 364 หลายเดือนก่อน
Part 1 of what I chose to video and then throw together in a pile for you. Feel free to ask questions. Hope you find something of benefit to you or at least mildly amusing. I solved the valve wrench issue by modifying my water meter/valve tool. Maybe I'll do a Quick Tip on it.
Shop Visit - 12 July 2024
มุมมอง 175 หลายเดือนก่อน
Quick video for a friend of mine after troubleshooting an electrical issue...
Tips & Tricks #1: Keeping the Oil IN the Oil Filter (5.9L & 6.7L Cummins)
มุมมอง 815 หลายเดือนก่อน
Oil filter plug and a 4" D&W "cleanout fitting" will stop 99.9% of oil spills from your filter elements. I don't do production value... sorry. Just information.
On-Demand Water Heater DEEP Flushing
มุมมอง 68 หลายเดือนก่อน
So, if you have at/near/above "11 grains" of dissolved minerals in your supply water, you NEED, no MUST have treatment before the water heater to REMOVE the dissolved solids or they WILL deposit INSIDE your heat exchanger and accumulate until it heats poorly and flows worse. This is a solution of 3 gallons of RODI water (0 ppm dissolved solids) and 1 pound of anhydrous citric acid. It's a big s...
"latch.it" RV Door-Lock GEN 1- Disabling sounds
มุมมอง 128 หลายเดือนก่อน
This is an old video of me helping out some TH-camrs who were sponsored by latch-it (at least at the time). Their video had some "issues". But this video became a pretty good DIY instruction on disabling the buzzer/alarm on the Latch-It (generation #1) RV Main Door Lock with remote and key pad. So I am making it public.
Salem FSX 260RTX Shower Point
มุมมอง 68 หลายเดือนก่อน
Final report on Shower Point warranty claim. Work complete. (Old video of my video documenting completion of the warranty work I was allowed to complete on my OPEN trailer by my dealer and Forest River. It became necessary when the cheap Chinese crap shower point popped open on the road and I go home to no shower want and an unusable hose.)
Planning a Tub/Shower Waste Relocation
มุมมอง 48 หลายเดือนก่อน
In the middle of the longest bath reno in human history. This is the day I dug out the shower drain and waste to see our options for putting in a tub with a much different drain center. Filled an ice chest with the dirt removed. Going to replace it with playground sand and re-cap it with portland cement rather than bitumen. We did not move the drain/waste drop. The HVAC condensation waste made ...
2014 Ford Fusion Titanium Coolant Flush/Clean/Drain/Type Swap #1
มุมมอง 20Kปีที่แล้ว
NO Narration. Kill the volume. Just a loud Eco-Boost engine at 2750 rpm pumping fluid out of coolant system into a bucket while adding nothing but de-ionized water to the reservoir.
2014 Ford Fusion Titanium Coolant Flush/Clean/Drain/Type Swap #2
มุมมอง 6Kปีที่แล้ว
2014 Ford Fusion Titanium Coolant Flush/Clean/Drain/Type Swap #2
You might notice that I carelessly tapped the left-side buttstock against my pistol rear sight. Yes, it put a small, new scratch. It'll be fine. <smile>
Feel free to leave comments, questions, or suggestions for what part of the process I should film next.
Level of ingenuity and disciplined organization I aspire to be 🤙🏻
I do apologize for the vertical phone video. I'll try to avoid (or change aspect) that aspect in the future.
Let's reinvent the wheel while we are at it
Not exactly sure what you mean. Not claiming to do anything other than offer a tip to other folks who need to prefill a filter and don't want to spill oil all over. Maybe you'll get something useful out of the next video. <smile> Be well, dude! <smile>
Nice job! A close up of the motor and jack-screw assembly in operation would have added some valuable insight..
Yes sir. It would have. It never occurred to me that I would publish this video. <smile>