วีดีโอ

U gunna do paint urself?

Sheeesh

Очень много слов... дела нет.

Bro lol i did the exact same thing man, but i ended up modifying it so i didn't need to drill more holes

Excited to see more videos man, keep it up! I have an e36 m3 that I bought in great condition and I've only kept it clean and done tasteful mods. I'm always tempted to find one a little more beat up so I can really dig into it. your videos are inspiring!

We are in the same boat just bought a 325is 93 converting to m3 keeping the m50 and going single turbo

Straight, rust-free chassis is the key to an e36 build and you seem to have lucked out there. Subbed and looking forward to the build. Use of an M54b30 crank in the engine "refresh" could be worthwhile considering. Looking forward to the build!!

SO COOL BRO

Bruh! Affordability, aftermarket support and parts availability is key to this platform! I have owned my 1997 E36 M3/4/5 for 13 years and it has been a great experience learning, wrenching and driving it. I've had to do the brakes, clutch, rear main seal, suspension, window regulators, door lock actuators, oil changes, bushings and coolant refresh. All of that work was done by me and all of the work was pretty straight forward. No crazy issues or ultra specialized tools. You're going to love this platform. BTW the ZF transmission is pretty awesome! I also have an E46 with the 6 Speed Getrag and that tranny is good, but not as smooth as the ZF. I purchased for $8K and over the years have spent $8k in all the repairs above. At this point, the car is very well sorted and it just drives amazing and handles likes its on rails. Truly an awesome and visceral driving experience.

Finally a step by step journey About an e36 I hope to cop mine later this year

🔥

No side blinkers?!

I’m totally bought in. Looking forward to the build

More holes bro, more holes. Cheers

I’ve fully built/upgraded my $1.8k e36 m3 over the past….almost 5 yrs 😢. It’s been a lot of fun and a lot of stress. Wish I would’ve vlog’d it. I have posted all my progress on instagram throughout the years. It’s nearly complete and hopefully will be on the road by spring.

The thermostat has an arrow that notes it needs to point straight up. If you have issues with it bleeding or maintaining temp, that’s your problem

Love your content bro❤❤❤

The rendering on top big Big UP from France 🇨🇵👍👌💪😎🔥🔥🔥

Don't foget to remove the original covers for the OEM jack, otherwise even when you remove the cover on the sideskirt you wont be able to use a factory type jack.

A+ bro great vid great content great editing good music, perfect video bro keep it up!!

I literally just did all this

Also for your side skirts I know a cheat code on putting them on use self tapping screws under the jack pad covers. Make sure they are small enough so you can hide them under the cover and then use 2 self tapping screws where the side skirt hugs the wheel wells. You can refer to the oem mounting points from pictures where they use plastic rivets to mount them also don’t forget the rubber seal that goes in between the skirt and the body. There will be a small gap if you don’t use it

Also why do you prefer the facelift nose panel over the pre facelift?

You’re supposed to install the crash bar into the m3 bumper first with plastic clips then you mount it on to the 2 frame rail pieces and then you install the 13 mm nuts while pushing up from the bottom to close that gap under the nose panel

You’re supposed to install the crash bar into the m3 bumper first with plastic clips then you mount it on to the 2 frame rail pieces and then you install the 13 mm nuts while pushing up from the bottom to close that gap under the nose panel

Great timing I just picked up my ‘92 325is few weeks ago interested in it build and gna follow it. Got very similar cars and I’m sure I will learn a thing or too. Mines pretty clean minimal fender rust in one side, engines for 250k kms and just excited to have a project to always tinker on

You're brave man. I don't mess with body work lol. I had the same problem with those side skirt clips. Only the OEM ones worked. Same thing goes for window regulators when you get to that. I also recommend adding a few more holes for the skirts. Keep up the great progress 🙌

Bravo alex! Mangas eise!

Do you think that’s the same body kit garagistic sells?

no matter country every e36 ends up with alibaba m trim 🤣 guilty too

Expensive but worth it, keep up the great work ✌️

That expansion tank is probably the weakest part of the system now

Great video! but you definitely should've changed the water pump while you were in there!

Man based on your previous builds this thing is gonna rip! Looking forward to what you do with it. Isn’t it funny how the expensive projects turn out to be duds, and the cheap ones turn out to be a steal. It doesn’t make sense but the same thing happened to me 😂

I'm interested to see if that leaks around the thermostat housing. It looked like the block had a lot of corrosion around it and that is usually why people use sealant. The headlights are E36 P36 lights, DEPO took their projectors from the E46 and put in them in the E36 headlight housing. They illuminate the road much better than stock E36 headlights. That AUX fan is a disaster though.

Thanks for sharing. What year is this e36?

Would it have been better to start with a car in slightly better condition?

U greek?

Nice job! Now for the next project boost it😜

Wrap it!

Gotta have that AC!

Trump baby!!!

That was so pleasing to watch, can’t wait for part 3!

Smoking deal.. Man that car has seen better days, but theres room for improvement. Once the interior turns around it makes the car less of a bomb. Looking forward to seeing the progress. My car was in identical condition when I bought it and almost done. Cheers, best of luck.

that is a non m cluster with a M badge sticker