- 21
- 7 237
Aero Elastic
เข้าร่วมเมื่อ 12 ก.ค. 2014
Scale RC 4x4 & Toyota 4-wheel drive
WPL c44 flatbed - performed better than my mn82 on same trail. Link in description
Did the exact same trail as my mn82. C44 did better-higher clearance and wider tyres th-cam.com/video/rIVkAI3Q6XA/w-d-xo.htmlsi=ipcIKHFUGgQmwuk6
มุมมอง: 110
วีดีโอ
MN82 Brushless vs Stock motor!
มุมมอง 942หลายเดือนก่อน
Swap out the stock motor with Aliexpress outrunner. The control is brilliant! ￡29.34 | NEEBRC 2322 2600KV Outrunner Brushless Motor AM32 45A ESC for 1/12 RC Cars MN82 MN99S MN168 MN78 Crawler Upgrade Kit Combo Parts a.aliexpress.com/_EGq2BlQ
RC4WD 1/18 Defender Gelande & Toyota 80 series HDT
มุมมอง 672 ปีที่แล้ว
RC4WD 1/18 Defender Gelande & Toyota 80 series HDT
RC4WD 1/18 DEFENDER GELANDE & LAND CRUISER 80 series SLOW CRAWLING
มุมมอง 733 ปีที่แล้ว
Edited by my little girl, driven by her & my boy
Rc4wd 1/18 Gelande ll Defender on Milestar Patagonia - Crawling!
มุมมอง 2264 ปีที่แล้ว
Motor is from Tamiya mini Low Speed 4 speed motor
Rc4wd 1/18 D90 garden trail with reduction motor
มุมมอง 1.1K8 ปีที่แล้ว
Rc4wd 1/18 D90 garden trail with reduction motor
Do you have experience with 370 31T brushed motor too? What is better, 2322 2600kv NEEBRC or 370 31T for Rock crawling? Also will those two be able to carry my MN99S 1.7kg.. How it your current motor for slow rock crawling?
@nosfer4tu188 hi unfortunately never tried the 370 motor. But the 2322 slow speed for crawling is very good. But if it's a slow "dead" obstacle crawl, like stuck on 4 wheels against big rocks, the 2322 motor can run out of torque, once released the throttle and pressed again you will get full power again. I guess it's a way the 2322 esc protects the motor?
@@aeroelastic6736 Ahh I see! By the way, by "stuck on 4 wheels" Do you mean like 4 wheels have ground contact but is trying hard to climb a large obstacle and it just cannot get up?
My mn82 weights 1.2kg. 1.7kg is pretty heavy I would say for this motor.
@@nosfer4tu188kind of. All 4 wheels Against challenging obstacles.
Thanks for sharing. This is the metal kit. Took a while to assemble but worth it.and the 2 speed box is handy for trail walk
@@aeroelastic6736 Yes, and for nipping between obstacles : )
Thumbs up for reminding me how good the C44 really is! I never bought one; instead, I bought an MN45 and did my best to bring it up to the C44's performance level. Looking at this video, I'm not altogether sure that I succeeded!
what's the advantage of WPL's ESC compared to MN's?
Wpl esc allows higher current, up to 15A. MN only to 7A. Hence WPL esc immediately gives much more torque at low speed.
But you need to upgrade the stock electronics to a full receiver type like Dumbo rc 6 channels or such. So the fast and slow mode will not be there. But this brushless system will cover the full range of slow to fast...
This is what I installed:😊 ￡63.19 | NEEBRC 2322 RC Crawler Outrunner Brushless Motor 5.5-9V CW/CCW 45A ESC BEC for MN82 MN99S MN168 MN78 Off Road Model Car Climbing a.aliexpress.com/_EJ7ar44
What brushless did u install? Is the fast and slow mode still there?
Where is the full video of installing brushless motor?
Sorry didn't take any...
How was the high speed mode on brushless vs stock?
@RaphaelAaronJabson I would say brushless full speed is a bit slower. I swap out my stock esc almost immediately after I got the truck, replaced with Dumbo transmitter and WPL ESC. The high speed then was faster than the current brushless max.
Hey bud looking to get a 12v 1000rpm motor will a 10,000 Miliamp power bank run it at full power you think ?
@@TheEpicCosplays the N20 i used was only 3000rpm or so, and it was very slow, not worth it. I have swapped it out. But if you can get a 1000rpm one it might be ok
@@aeroelastic6736 ah ok thanks for the reply just as looking for a fast as possible motor as making wolverine class
Claws
new sub 👍. How did you lift it like that ?
For the rear, i flipped the leaf spring to the top of the axle, and removed the black longer leaf, otherwise it will make the whole rear end very stiff. For the front, i use longer screw and a spacer at the mounting points. And change the springs only to a softer set. It is a good balance in my opinion. The stock arrangement is a bit too stiff.
In this video, th-cam.com/video/vu4abqzA6bU/w-d-xo.htmlsi=Mby9cLRD2bGu1Fd8 the front spring was stock, but its too stiff for me, so changed to a softer set. Like it better now.
@@aeroelastic6736 thanks for the tips
@@aeroelastic6736 thanks again
What kit is the lc80
It’s the 1/24 FTX Mini outback, or the RGT 1/24 Barrage if you are in the US I believe. I am in the UK. I have put a 1/28 scale Landcruiser 80 body on. And use the low torque N20 motor with gearing for the gearbox.
Love the Landy 🤗 Greetings from Austria 🇦🇹🍻
Thanks, have a bit of time to play with it now as staying at home more...
This is with the TAMIYA motor, see;www.rccrawler.com/forum/micro-scale-rigs/618006-ftx-mini-toyota-land-cruiser-80-series.html#post6020450
Hi , did you ever get the car sorted , I have exactly same issue as what you have here www.e90post.com/forums/showthread.php?p=24591723
What rpm motor use Tanks
It’s the N20 reduction motor. 60rpm
Where did you buy that motor? Thanks in advance.
Banggood, eBay, or Amazon. Do a search for 'n20 motor'. 6-12v DC
any chance you have a link to the motor you used?
Banggood, eBay, or Amazon. Do a search for 'n20 motor'. 6-12v DC
dig your setup. what motor did you run? Thank you.