วีดีโอ

Worst video

Interesting pattern choices at 0:16 and 0:18 😜 looks like you decided not to keep it that way though!

Español

Looks good

So many questions. Horrible installation video.

nice

Can you put these on deck joists? Or would they flex when you walk on them

You should’ve got smarter Mexicans to do your insulation. They used Douglas furring strips which the termites will come into and eat then dry rot will come in after that. All the fasteners were just drywall screws. They didn’t pre-drill the material as you advised they did a horrible installation.

I've now got New tech Wood after having a fully erected deck

If you think erecting your deck isn't going to be hard, think again!

I erected my deck after watching this video, thank you so much! it's rock solid!

Can you install this vertically?

I like how you say to use stainless screws, but yet these guys are running drywall screws. What about windows? What do you do around them?

You recommend I trim for multiple horizontal boards but almost all samples on website doesn’t have this.

Might be ok in the desert where there is no rain... Imagine the mould buildup and rot behind in a wet climate? Looks good though.

Damn proud to be from Minneapolis, Minnesota !!

My concern is having any strong or heavy wind lifting the perimeter tiles where fascia is installed! Any comments or suggestions about this? I'm doing about a 900 sq. ft. area over existing patio. If this becomes a problem, is there a way of securing the fascia piece to existing patio?

Show how it looks now?

Where can I buy this product?

Can you put this on top of TPO?

@ 1:04 i noticed that if you don’t pre-drill the screw holes, your likely to break the vinyl trim as seen @ 1:04. Pretty brittle stuff

I thought that you only need one screw in the center to fasten it, not on the ends as he said.That way it can expand in either direction????

My wife and I are looking at doing a horizontal fence using Hoft posts. She like the looks of your hollow UH02 in Walnut. Do you have any recommendations?

How do you install these over the concrete patio stairs and the raisers?

Number 667 like had to do away with that 666 bruh 😂

I measure 13/16 in finish trim, but setting posts in concrete to 24 9/16 , 😂

I’m installing this right now as ceiling soffits. Looks great.

Shitty explanation

So confusing

Are there color matched screw plugs for the caribbean blue deck boards? An, no routed the entire length of the board. That's something I didn't know. I wish the caribbean blue was available on Columbus profile, but I will have to route for the fastenters since I don't want visible screws. Don't think I could get that L-shaped groove carved in to the Cortes board Unless I could fit a dremel blade in somehow. Would be a pain, but I could possibly do it, but then would need to get some sealant inside where I cut. I want to make a small landing outside an exterior door but need to figure out the measurements and how many boards I would need. Again, I wish fascia board was available in the caribbean blue. Is it just an unpopular color? I suppose worst case I can use primed PVC boards and then paint them for some of the edges and for riser covers on the stairs. For people who aren't using boards on the sides, it would be nice to get some sort of end caps for the Magellan and Columbus boards. Although, I suppose it would look nicer to use boards on the edge and miter them to hide the edges, but not everyone will want to do that. Shoutout to Richard Lam for answering my e-mails and giving me some info on the router bit size (1/4") and letting me know that some of the boards are not available in the caribbean blue.

Can this be installed directly over joists of a deck, or does this need decking installed below it for structural integrity?

Why do you need furring strips if the clips already create a 1/4" air gap?

Great video, but if you are installing cladding between brick, or gable, how do you install end trim?

Gotta love how they dont tell you anywhere, on their videos or website, of how to cut them with a curve. Not all decks are square, some are rounded.....

I don’t know but this material scratches easily. Currently installing one.

Doesn’t at all tell you how to install

Are there levelling plates for uneven surfaces?

Trying this tomorrow ill let you know how it goes

What about freezing if water gets trapped under will it lift and break.

@ 3:30 I dunno if I like that 1 inch gap under the window. Shoulda started off a tad higher there “licensed contractor” 😅

What color is shown at the beginning of the video :37 second in?

I'm considering composite siding for my home. This looks like a neat product.

I sure would have applied some stain or paint to that old wood under the deckwood. But not my old deck that looks on the verge of collapsing.

NICE!

You know it looks real when it looks like it needs a good dethatching lol.

Product is discontinued.