วีดีโอ

Sparkos has 30% off right now for Black Friday

I also think, that B is the better Version because it sounds less harsh in the higher regions.

I like both :) maybe B feels tad brighter and bass little bit different

One is fun but two is glue!😊

The Sparkos sound more musical. The JRC have more of a hard edge to the sound, but also sound flatter and less dynamic. It’s hard to put into words. Sparkos is good. That’ll do 😊

In my experience rolling opamps, being honest with myself, I have only had very, very few times where I have made an improvement. The thing is, the opamps circuit needs to be tuned as a whole, putting in AD827's for example can cause oscillations for seemingly no reason. My personal thing is, if there are only uA702 or 5532s or something truly terrible, it isn't worth swapping unless you are going to monitor everything with an oscope. Changing a 5532 to a 47920 pretty much always is a clean problem free swap, and the 49720 is a cheap, but pretty nice IC. If you want something that everyone raved on about in 1 point in time, and it's actually the IC that has provided me the highest change of any I have ever tried, try the Burr Brown (now Texas Instruments) BB2132 (assuming you are using 2ch versions). You used to be able to get them through Jaycar, and so you could be 100% sure they were genuine, however I google| them just a day or 2 ago, unfortunately they only had the 4ch 2134 listed. Those things were really crazy, I've never had the midrange entirely collapse to dead centre like this before, like everything went to mono or something, but the top end was still free to move around. Never had anything else make such a massive difference.. My personal favourite, not that I've tried that many, maybe 20, is the LME49720HA, they are a metal can version (round package), more military grade, better than those plastic types, had to simply put the legs into DIP8 sockets. They got much warmer, but I got round headsinks for them that slid over the top. I believe the PSRR/CMRR is 140dB, sleep rate of >30V/ms and the data sheet even has a section about how low distortion they are that they have a special way to be measured to Audio Precision tools can even measure it. At 600 ohms (for headphone amp use) THD+N @ 1khz 0.00003% and IMD 0.00005%, super low settling time of 1.2ns at it's max of 100pF of capacitance before output isolation, with excellent phase margin and stability

So will you boost to match the target curve?

Can you test what UAPP does?

Great fun! Just don't try to show the folks at Audio Science Review hahaha! Love the rig btw.

What no comments? This is so unique ....I love it. I've been around car audio for awhile.....yeah.....lol.....and I've not seen anything quite like this. I'm subbed.

This is real 3D printing. You are in control.

How good of SQ are the Audison lrx & Vrx amplifiers? How much better clarity of sound does vrx have vs the Lrx amps?

Question can You tell me if this Audison Lrx 4.300 amp gives better sound quality than the Mosconi gladen pro amplifier? Im in process in deciding on pullin trigger for the Audison lrx amp if worth it?? Thankyou

"it's like a bath, of goodness"

Thx bro

What is the benefits of using these units over a 14v dc amplifiers?

Do they make wider tips or larger pens?

Why would you install a SQ sound setup to a noisy entry-level car?

Dang! I've used those 3D pens before and I was always terrible at then, love the dedication!

I bought one of the pens because of you. It has been very helpful.

I love your creativity and unorthodox approach to audio.

Those little drivers are so dang cute.

How you see the mirrors is this legal

First vid ive seen of yours, but WTF am I looking at? Spider halloween alien SQ car?

What are you running for sub ser up?

How are your two midrange crossed in conjunction with each other?

I'm interested in getting a 3d pen but Amazon only has toy looking units. Can you send a link to what you use? Thank you in advance

So smaller is better?

It was a fun day despite the weather.

Convex sure sounds nasally.

Nice weather!

Sounds like a CV joint clicking

Something wrong with driving shaft or ball bearing

That your time alignment is wrong? 😅

Capcut

You dont like bass in your face?

Interesting. I do wonder why they make 192kHz releases in the first place though. Even if a speaker can reproduce those frequencies, people can't hear them. Maybe it's so the bats can enjoy it.

Only listen to start 6 seconds. Especially seconds 4 to 5.

Tidal tidal.com/browse/track/4128374

Apple geo.music.apple.com/au/album/cherokee/1443660487?i=1443660632&app=music&ls=1

Listen to Cherokee by GRP All-Star Big Band on Qobuz open.qobuz.com/track/502626

seal II by seal is like this aswell ... wonder why

Oh that's a familiar song 😜

You may also try feeding 2 amps from each side with one PSU and Y-cable. For example 1 PSU for L 6"+3” and another for R 6"+3".

Yeah, there is no replacement for raw voltage (amplifier output voltage), thats why I use absolutely massive amps, I've got a Arc 2300SE @ 330wrms /ch probably my most exotic amp I just use for my tweeters, I was using a MRV-T757, bridged, per tweeter, MRV-1505s bridged for each 3" mid ('bout a thousand rms each) and another 2 1505s, each BTL for my woofers. You want amps with not only very, very high output voltage, but a distortion curve that lowers vs output power, like my 1505s, the more you turn it up, the sweeter it gets. There's no chefs kiss emoji

You're lucky to have magic button to switch to better thing :)

What are you powering all these with? Because I had this same idea and now I really want to do this.

Spiderman was there

Lotta anger in that music