วีดีโอ

I would have just bought a longer piece of rebar.

You support me I will support you

Good bro

Todo muy bien pero por favor ponele otra música esa está para 💤💤💤💤 dormir

For cripes sake its not a woman. Use your tool z.

Quicker to use your fingers !

)))) голь на выдумки хитра

Nice ❤

Nice

Полуавтоматом так не варят

No

Wtf did I just watch

You can try laser welding for this kind of welding

On my GB-98 test, in welding rebar. It states that you must clean oil off rebar and then over lap rebar X inches depending on diameter of rebar it's self.

Great

The secret is to not do this.

Rio or rebar doesn't get welded, just use steel wire and crimp them together

Thank you

ER6011 would dig right through the rust and mill scale with far better penetration than that trash can wire! JMHO

Am i missing something, or is the cutting away part not inverted here? I would expect the remaining radius pieces to be the sum of all the small pieces of papers' width. But here the widths are marked and then cut away? And this only fits because the remaining pieces were approximately the same size as the pieces cut away? But i still liked the vid :)

Thank you! You're doing a great service for the public.

Apparently magnetic squares are only "rarely known" to folks that can't put down a tack without sticking the rod (9:03). Running your ground line to a magnetic square isn't really useful, it just makes the square harder to deal with and increases the chances of misalignment. Just use an off-the-shelf mag square and stick a conventional ground clamp on it.

Zigzag motion or

الة تصنيع العلف البقر

Okkkkkk . . . .

Doesn't look very thin, could MIG it continuously with np.

Step one to welding galvanized: dont use fucking arc. I dont even know where to begin with retarded "how to weld" channels like this.

this is why you always grind galvenize first!!

The irony

I'm one of the few who happen to know about a pipe wrench. Ask me about the time I used a pipe wrench to loosen a nut or a bolt. Oh you don't know what a not or a bolt is? Gather round kiddos. I'm one of the few who know this stuff.

I hope you took every necessary pre-caution as the fumes produced from welding galvanized steel are quite toxic, i would honestly recommend putting a caution in your description, personally i would never weld galvanized unless it was absolutely necessary.

Wrong

Dude no.

Nice pipe wrench.

How many junk welder channels do u have? Ur the only one with that poo poo wire brush and goofy enough to weld with rubber coated gloves.

I watch other tecni. U make complicated

Okay, you beveled the rebar. Where's the preheat? Most rebar has a lot more carbon than structural steel.

Wow a.wrench

Few people do, yes. Including yourself.

yeahhh, don't quit your day job buddy.😅

Terimakasih sobat untuk triknya...

Thanks brother

also rebar contains too much carbon for good welding, there is special order rebar with low carbon for welding.

Oh where to begin . . . . . First and foremost you compromised the structural integrity of that mechanical tubing when you cut it and didn't fill the corners, so there's that. Second off you did not prep ANY surface, used a 6013 . . . looked like a 3/32 and didn't actually weld. All you did was take something somewhat strong and destroy it. Tacks are NOT WELDS . . . again TACKS ARE NOT WELDS. Those fish-eyes are stress risers and you probably have slag inclusions inside with them. That broken tack after you were done with the first side is what you're doing all the way across. Tacks don't penetrate and fish eyes don't hold. The only secret about what you did is that it's lipstick on a pig and people that don't know what they're looking at will think it's great. REBAR.

Many know this method but they always try to get it done faster and with less material cost.Do you have any video on Flux core? I left stick welding and do only flux core its easy n fun.

That white zinc smoke is toxic. Go take a real welding class.

inhale that zinc smoke

Is this your first time welding? Ridiculous

thank you I like your video

Good welding brother❤❤❤