- 11
- 396 836
Tiptoeinn
เข้าร่วมเมื่อ 15 ก.ค. 2013
f250 f350 7.3 turbo pedistal ebpv delete DIY
In this I take you on a quick easy cheap way to fix your oil leaks that are prone to happening on a turbo pedistal in a obs ford.
มุมมอง: 9 745
วีดีโอ
ls1 e36 paintprep & highlights
มุมมอง 3107 ปีที่แล้ว
Preping the e36 for some fresh paint before the next event! I do not own this music all owner ship to rightful owner Tags: e36 drifting cars vlogs ls1 swap how to paint
Lifted gmc sierra on 22x14s
มุมมอง 1.6K7 ปีที่แล้ว
Reil creative made an amazing film of my sierra all credit goes to him. So much talent. Lights are prezy workz flow series its on a 7.5 lift -no body lift 22x14s on 37x13.50 atturo tires Like comment subscribe.
LT1 front main seal replacement
มุมมอง 28K8 ปีที่แล้ว
Tools you'll need is 16mm for crank bolts 17mm for crank slide A sleeve to press seal in Seal puller tool or screwdriver
2004-2009 Nissan quest front wheel bearing replacement
มุมมอง 220K8 ปีที่แล้ว
In this video I take you thru the process of replacing a wheel bearing in this Nissan quest enjoy. I do not own this music. Copyright can suck a fatnut
How to change 2011 altima tag lights
มุมมอง 15K9 ปีที่แล้ว
In this video I show you the simple task to change out your tag lights on all newer model altimas. Follow at your own risk
How to remove bed off 04-12 chevy colorado
มุมมอง 75K9 ปีที่แล้ว
I show you what it all takes to remove the beds off a colorado tools you will need are -18mm socket -extension -ratchet or air gun -Phillips screwdriver -muscles -common sense I by no means take any responsibility for anything that could go wrong do this at your own risk. I do NOT own this music all ownership to wright full owner
chevy silverado angel eyes
มุมมอง 6K9 ปีที่แล้ว
I do a custom set of angel eyes on my obs silverado. And show the results. Lmk what you guys think in the comments below. Just wanted something different than what the market had to offer..... Like, share, and subscribe! I by no means own any right to the music in the back ground.
how to replace ignition coils nissan maxima 3.0
มุมมอง 28K9 ปีที่แล้ว
This is NOT A step by step procces just an overview of why is needed and done while doing this job All rights reserved to rightful owner of music Double ds garage more to come SUBSCRIBE! Share! Like! Comment!
prizm, corolla valve cover gasket change
มุมมอง 11K9 ปีที่แล้ว
This is not a step by step video. Just showing you basics of what all needs to be done and what you will need. Thax enjoy! Will be doing more videos in future my buddy just needing this done ASAP so went ahead and filmed it. All rights reserved for music to rightful owner.
Just what I was looking for. THANKS
Thanks broski very easy and straight to the point.
18mm bolts btw for anyone wondering
good vid bro. Thanks for sharing.
I'm making my own like yours, real angel eyes almost look alien or menacing when it 4 eyes
Yeah, some tough spots to see, but still gives me a good idea of how to go about it! TY4SHARING 🙏
Oh you have no idea how much this helped me. My fuel pump went out and I really don't have a place where I can drop the tank. Now ik i don't need to
Thanks bro helped me out a ton!
So you mean to tell me, it's that easy(maybe a little more work for the back)? Shop is talking about $1200
Thanks for sharing
What size are the bolts
You from Oklahoma bro ??
What if I leave the rod alone my new kc turbo doesn't have it. I forgot to orderc pedestool delete
Nice tx
Never reuse a cotter pin.
Just did this on my 2009 Nissan Cube. Axle nut is 30mm, torque is 92ftlbs, bearing bolts 65ftlbs, shock bolts 122ftlbs, caliper bolts 62ftlbs, wheel nuts 80 ftlbs. My sensor would not come out but the bearing came out and went in around it, carefully!
Well, after getting stopped for only one of my lights being out, I’m on my way to go change them now👌🏾💯💯
Not a very helpful video to anybody, plus horrible music.
Starts with tubes already removed... You missed a few steps bub.
why was it necessary to remove strut bolts.
So you just cap the hole and put the plate and snap ring back on ?
Thx for this video
Great video. Im trying to remove the 6 bolts. They just spin and spin. Is it just a nit on the other side or did I break a welded nut?
Awesome video, thank you! I hope to get a replacement bed for my Canyon. Previous owner backed into something and the shop used bondo. Needless to say, my bedside is rusting.
This seems easier than dropping the tank, I'm planning on cmchangibg the filter on the fuel pump so this is definitely gonna be my go to method
I k ow this video is old but hopefully I get a answer I have a 06 Pathfinder with the 4.0 LE model. Got my bearings today new ones have a harness on end my stock gave no plug in the end just goes to bunch of wiring under hood.
This is rhe best video. Especially reminding to remove the ABS sensor 1st.
Very helpful!
Ty very helpful, wish me luck lol
WHY DIDNT YOU FILM WHEN TAKING THE BED OFF??
You ain’t got to do all that
This is all I needed to see thanks
Great video. Especially when you generally know how to do this job. I'm an old schooler and am used to beating those inner/outer bearings out with an over sized socket. Thank you for the upload.
DOES IT MATTER HOW U PUT THE HUB BACK PLEASE HELP AND RESPONSE THANK U
Yes it does
Forgot the back plate.
Yea buddy! Six years later glad you made this video. Changing fuel pump on mine too cause the fuel level sensor went out.
your lighting is so bad and your music sucks.
Bro, where did you get that NEW whole hub & bearing???, Just bolt on!! I can't find it at AZ or Orielys
Yeah..there not that easy to get to if u don't have extensions.. a breaker bar.. so on so forth..
This makes it seem a lot simpler than I had thought. I’d like to do some rust maintenance on my ‘05 Colorado. What type of cleaning did you do and did you repaint or spray the frame with anything? Thanks!
Glad I could help! All we did was give it a real good clean we didn’t have rust issues but that’s a really good time to coat your frame if it needs it.
Thanks yall
Cool video
great video, just couple things....you forgot to put back the shield plate behind the wheel bearing and i always have seen people put grease in the inside for the axle rod. is all. thanks again for the video
How much bro?
Why did he put back the dust plate lol there was nothing wrong with it
Oh I hope I have that size in my ball joint kit. I don’t know why I wouldn’t, but I did buy it from a meth head. It still had the price from Napa, he tried to get me to pay more. Sorry pal, you’re going to need to sell me that drill press too, to get enough cash for your next high. Bought that for a hundred. Poor bastard used to be a normal guy too.
*Great product🌗 **allabout.wiki/FrontWheel** Low price and look durable. These wheel bearings x2 took care of my steering wheel play. Well built in my opinion. Perfect fit. No more annoying ABS light on.*
For those who are doing their diy projects, make sure you follow your manual for the torque, don’t just tighten your nuts to the extreme.
Thank bro helped out!
Where is number 3