วีดีโอ

Great advice. I can only get good results about 50% of the time. I will follow your method and I am sure i will get much better.

Nice video. Do you have a source for the small burnishing tool you use? I can only find large ones in stores

the other day i was listening to 'every tool's a hammer' by Adam Savage and he mentions these things. never knew they existed

would be a good video if you dropped the annoying backround music. Not everything needs music. When there´s no value in adding it, just don´t.

Why do you not push the burr out on both sides so that you have two edges on each sharpening session or did I miss something or would this not work?

You might say somethingabout what sort of file you used and that scrapers need to work with grain in the same way planes do.

Wow! I wish I had half of your patience

Where'd you get that case for your scrapers?

Lovely piece of artwork, well done 👏

This is a terrific and helpful video. Thank you! You've earned a subscriber.

wow! beautiful work!!

Brilliant, works much better than my previous method. It's quite surprising how little pressure you need to make the edge. I used the round chrome stem of a screwdriver. I also found that 1000 grit seemed to work fine as the finish. Thanks for posting. BTW the oil is essential as otherwise the metal edge tends to rip.

Excelente trabajo. Si señor!! 👏👏👍

Tgankyou

Beautiful piece But I must ask doesn’t that combination of wood finish, cause yellowing over time?

Great video, to the point.

After cutting your dovetails why do you leave the visible mark line across the board??? Never understand why people do this, just sand them out.

Do you have a source for the card scraper pouch? I've been putting my scrapers in a drawer and this method is far from the best.

One thing is for sure. Sandpaper dulls the wood whereas a card scraper keeps the wood looking natural.

Why do most woodworkers mark their tail boards all the way across and then leave their marking lines so they’re visible??? This looks very unfinished and takes away from a finished product. I’m not a supporter of “because that’s the way you do it” mentality. I mark mine only where needed, then the lines do not show in the end. You can at least sand them or plane them away very easily. Just fyi.

I love it and found it most relaxing to watch thankyou

For the first time ever I have managed to get shaving off of my scraper, thanks to this video. Thank you!

Beautiful work mate!! Thank you

Nice work, but.... eye protection!

Beautiful piece of art! Great job!

Nicely done 🔨

Tolles Holz Tolle Arbeit. Ohne Musik wär's VIEL besser

I love my scrapers. They leave the wood looking bright and feeling very smooth. Whereas heavy to medium grit sandpaper leaves it looking dull sand feeling fuzzy. It took some time for me to learn the proper way to sharpen one. Not everyone does it the same. And some books show the scraper being burnished at a 90 degrees. It puts a burr on both sides.

hmm.. You mention simple, but I've never seen any other way of sharpening a card. What are other ways of doing it?

That's the most beautiful box I've ever seen

I cannot understand why this video has only 509 views. Your woodworking and photography skills are outstanding. I'm happy to be one of the lucky 500.

Lovely piece! And it's great to see how well you take care of your quality tools.

THANK YOU for making a quick, easy, and most of all, STRAIGHTFORWARD guide. so much better that all of the 15 minute videos with midroll ads and sponsors that interrupt the video

Wish I knew this before! Unfortunately mine were left out in a dusty shed and got rusty but they should still work find for what I need

Great video as an introduction to the project. We need more of these videos your style and skill is well worth seeing more of.

I love it when you get big curly shavings, I’m a bit hit and miss when it comes to burnishing the card scraper.

Very nice work man.

could of done the whole thing on large wood lathe in half the time...just saying..

Essentially the same as many other videos, but VERY WELL DONE 👍🏻

Stupid question, but I assume when orienting the scraper you are cutting opposite the angle you create with the Burr?

So simple. Yea

Where can I purchase one of these trays?

i know this is an old video and you don't seem to be posting any longer. But wanted to say an awesome job. Great wood working and a classy looking finished piece

very dood video. i make music instruments (boyzoyki greek) an i use sharpen very mach

Looks great. !!!!!!!!!!!!!!!!! How many hours did you work on it (inclusive sanding). I for my person find music in this case disturbing

Good video. I like the use of the marker to ensure it’s bee touched uniformly. Have done that with cleaning up table saw sled runners too. It’s like using xylem blue in machining metal

I like the way you make the butterflies

I so despise music on these videos... I would rather hear the scratching of the pencil than that stupid repetitive waste of energy.

Very nice job. Thanks for sharing.

Awesome, thanks!