วีดีโอ

Do u know where can I find only glass for rear lights?

Thank you for this video. Very helpful!

Thanks for the great instructions, i solved this problem for two doors in my audi a6 c6

Même soucis, même réparation... Vous êtes au top !!!

Just what I was looking for! So valuable!! Thank you so much!!!

Merci beaucoup pour cette vidéo grâce à vous j'ai réparer ma serrure

Thank you!

Thank you man!! Thanks to you, i repair my own seat leon lock door!! 😊

Magyarok miért nem írtok ide 😧

Danke Bratan 👍🏼👍🏼👍🏼

quanti volt sono i led?

Никогда так не делайте! Делал в 5 раз аккуратнее, чем он и лопнуло стекло! Вырезал гравером, мини диском отрезным..уголок стекла заклеил..

misti greu idiot

why fucking music its not a fucking disco

Is microswitch i that lock hawe metter with light in cabibe and alarm and central lock

I had same problem with unlocking. This video helped, but spent 30 min to remove actuator from the door. It was the problem with bigger motor. I did not opened the motor, only sprayed it with wd40 through holes and turned it a few times. I learned I have to assemble the unit with caution as is dificult to put plastic rods in its place. if you dont do that, inner handle does not work. Thank you for this video.

Excellent fix. The resistors are 47 ohms. When you have re-soldered them, check with a test meter. The resistance should be half of 47 ohms because the two resistors are in parallel. Also I suggest you leave a larger-than-necessary blob of solder on each side to act as a heat sink. Fix the LEDs back in place with a spot of glue-gun glue on the two small white pillars. I used clear silicone bathroom sealant to reattach the front plastic.

Pewnie dobra robota dla osób, które nie znają procesu produkcyjnego lamp tylnych wyposażonych w funkcje światła LED. Metoda "naprawy garażowej przez tzw Janusza" pokazana w tym filmie po pewnym czasie negatywnie wpłynie na funkcjonowanie tej lampy: -możliwe uszkodzenie płytki PCB, skutkujące utratą funkji świecenia - praca bez odpwoiednich rękawiczek ochronnych -popalcowane rękami elementy metalizowane po pewnym czasie warstwa metalziowana zejdzie z powierzchni -wskutek sklejenia klejem ryzyko przedostania się wody do środka Pozdr specjalistę od naprawy

Amazing good job

Как потом собрать, чтобы герметично было?

Cześć! Szukam serwisu, który to naprawi. Warszawa

Cześć! Szukam serwisu, który to naprawi. Warszawa

Peut on acheter la carte mere

Thank you

Hi Do you have the OEM resistor value for the led I have an 470 cms resistor (47ohms) and the second have disappear and I don’t have the value of the second Thank you !!

The resistors that you point to at 4:33 burn out and cause the LED to go dim or not work at all - I scraped the burnt ones off and added a 200 Ohm resistor in its place and the lights are now perfect. Thanks for the video showing how to open the thing up. Has saved me a lot of money!!!

thanks a lot, one of the resistors in my right light was also loose, I put a new one in and it works like new again

Fix the dead led , Rear Lights. and what kind of leds do you need th-cam.com/video/_xMZbeyV4TQ/w-d-xo.html

как его вообще снять? не работает.

Haha, I searched like a dumb... Thnaks

Cool video. It took me ages to find out how these towbar should operate. Mine wasn’t working, because the pivot joint for the electrical connector to move was seized solidly. Only when I realised it was meant to rotate and move could I fix my problem. Your video was very helpful 👍

you are the best, god video Tnx

Thank you for the video! I had the same problem, fixed it and I feel proud of myself! haha! thanks again!

No sound kein Ton Gte swug

witam, masz jakies video, jak dalej?

My dumbass just fucking broke the taillight trying this out

Fuck

Good work! Thank you for a very hands on video! Especially how you make the video from the perspective of the watcher/repairman. Could you explain how you found the faulty component/-s?

Super Anleitung👍👍👍 danke dafür! Good job dude

why use a simple light bulb for 10 cents when you can have a LED and when it brakes it costs 400€...@modern solutions...

Diese Rückleuchte ist niemals so von Werk aus verklebt gewesen, sie war schon einmal auf und suggeriert jedem das sie einfach zu öffnen ist 😡

i do to mine and it’s break 😭 have bake it like 220 for 8 minit

Wenn ich das so mache dann bricht das Plastik ab

Thx very much!! Danke sehr hilfreich für mich .....

Даже греть не нужно было?

I broke my tail light, it didn't open, won't work

Mógłbym prosić o info jaki rodzaj/typ ledów jest zastosowany w tych lampach. U mnie kilka padło i chciałbym je sobie wymienić. Dzięki i pozdrawiam

witam. Jakim napięciem zasilić diody od świateł pozcyjnych? czy przy takiej probie należałoby również ustawić ograniczenie prądowe?

Odlocno

Bei mir leuchtet diese grüne licht nicht wo muss ich gucken?