- 6
- 43 733
StudentAid
เข้าร่วมเมื่อ 5 ต.ค. 2021
Hello Co-students! This channel is intended to help students to master their problem solving skills. I will be uploading 1 problem per video. Hope you understand it and don't forget to subscribe!
For the truss shown in the figure below, calculate the stresses in members CE, DE, and DF.
For the truss shown in the figure below, calculate the stresses in members CE, DE, and DF. The cross-sectional area of each member is 1.8 in2. Indicate tension (T) or compression (C).
มุมมอง: 3 051
วีดีโอ
A 12-inches square steel bearing plate lies between an 8-inches diameter wooden post and a concrete
มุมมอง 3.1K3 ปีที่แล้ว
A 12-inches square steel bearing plate lies between an 8-inches diameter wooden post and a concrete footing as shown in the figure below. Determine the maximum value of the load P if the stress in wood is limited to 1800 psi and that in concrete to 650 psi.
Determine the largest weight W that can be supported by two wires shown in the figure below.
มุมมอง 5K3 ปีที่แล้ว
Determine the largest weight W that can be supported by two wires shown in the figure below. The stress in either wire is not to exceed 30 ksi. The cross-sectional areas of wires AB and AC are 0.4 in2 and 0.5 in2, respectively.
The homogeneous bar shown in the figure below is supported by a smooth pin at C
มุมมอง 3.9K3 ปีที่แล้ว
The homogeneous bar shown in the figure below is supported by a smooth pin at C and a cable that runs from A to B around the smooth peg at D. Find the stress in the cable if its diameter is 0.6 inch and the bar weighs 6000 lb.
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure.
มุมมอง 19K3 ปีที่แล้ว
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa.
A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN.
มุมมอง 10K3 ปีที่แล้ว
A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine the outside diameter of the tube if the stress is limited to 120MN/mm2
Pano naging 30 yung 120?
Don't forget units cancellation.. tsskkkk..
Paano po nakuha yung 400000N?
1kn = 10^3n
Para tanggalin yung K sa KN ginawang 400000N mas madali i solve sa stress direct na macacancel yung N
For explanation
Thanks
Your video is amazing. So clear and visible
Can you solve the Fig P-112 for me please 🥺
Thank you so much ❤😍
What is the name of the book where you got the problem and who is the author?
Why is the summation of moment at c = 0?
Thank you po
شكراً على مجهود
Thanks for this good explanation 🤍
Can you tell me about this app which you are using for solving questions?
tama po yung MN/m2, equal na po siya sa MPa
N/mm^2 ata yung MPa lods
@@christianjohnbiol6789same lang ata yan lods MPA
@@JOEN-kr6yz hahahaahha ouh nga lutang ko pa nyang panahon na yan. sorry my bad
@@christianjohnbiol6789 oks lang lods, ako nga lutang pa rin STREMA. Kamusta lods? Engr na ba?
You're not even explaining it.
Plss answer this example Maam. The strength of longitudinal joint in Fig. 1-17 is 33 kips/ft, whereas for the girth is 16 kips/ft. Calculate the maximum diameter of the cylinder tank if the internal pressure is 150 psi.
More example Maam
No need to convert MPa to N/m^2?
Hi maam can I ask questions?
thank you are great keep going progressive