- 11
- 13 080
Squarebody Mob
United States
เข้าร่วมเมื่อ 10 เม.ย. 2022
Hydraulic Lifter Removal Tool
An easy way to remove your hydraulic lifters, especially if they're a little rusted in place...#chevy327 #squarebodychevy #smallblockchevy
มุมมอง: 462
วีดีโอ
Success!!! Piston Removal...
มุมมอง 1.6K2 หลายเดือนก่อน
I was able to remove the rusted pistons with just a small torch and WD-40...it worked very well...I've tried Trans. fluid, Evapo-Rust, and a combination of trans. fluid and Acetone...maybe those fluids are what initially started to break up the rust...I'm sure they helped...#chevy327 #smallblockchevy
Chevy 327 project
มุมมอง 7762 หลายเดือนก่อน
I'm slowly making ground on this motor, trying to get the pistons out...I only have three more to go...trying the 45% vinegar in the cylinder to see if it breaks the piston loose...#chevy327 #squarebodychevy #smallblockchevy
1969 Chevy 327 Update
มุมมอง 9863 หลายเดือนก่อน
I'm still trying to break the rust free on this motor. Any suggestions would help. #chevy327 #squarebodychevy #squarebodychevy
Found another Chevy 327 #chevy327
มุมมอง 1K3 หลายเดือนก่อน
Came across this 327 from 1969, stock bore, very dirty and rusty, but I have high hopes for this one. #chevy327
Chevy 327 teardown #Chevy 327 #smallblockchevy #smalljournal327
มุมมอง 5733 หลายเดือนก่อน
As I'm disassembling this 327, I'm finding pieces of broken pistons. I'm not sure what causes that. If you know, leave a comment.
1965 Chevy 327...300HP...
มุมมอง 2K3 หลายเดือนก่อน
Purchased a 1965 Chevy 327 to build for my truck. I've always wanted a 327 to build. I won't know how much work it's going to need until I start disassembling it. Should be a fun project.
Squarebody Column Shifter Swap #squarebodytrucks
มุมมอง 76ปีที่แล้ว
This is a very quick tutorial on how to swap out steering column shifters. This was done on my squarebody truck, but I'm sure it's the same procedure for all or most column shifters. I did notice that the pin hole was a little smaller on the aftermarket shifter, so I had to drill out the hole one size bigger..LIKE...SUBSCRIBE..SHARE...
Squarebody Cold Start
มุมมอง 1.6K2 ปีที่แล้ว
Just finished installing a new MSD distributor in the motor. I still need to tweak the timing. I just fired the truck up a few seconds before I recorder this video. Please like and subscribe so I can grow the channel.
American Racing AR61 on Squarebody truck
มุมมอง 1.1K2 ปีที่แล้ว
This is a better look at the AR61 Outlaw 1 rims on my truck. Leave a comment if you like them and please hit that subscribe button.
American Racing Outlaw 1 Wheels installed
มุมมอง 2.8K2 ปีที่แล้ว
I swapped out the rims with American Racing Outlaw 1..AR 61 series. I love the way they look on this squarebody.Please like and subscribe.
You only bore one cylinder and leave all seven std bored and get all piston and rods cut to way 10 grams under and 15 grams over send the oil to the top end faster to run the dry sump pantara
They are not rusted in place in most cases. This will RUIN the lifter bores. The lifters are mushroomed from wear. Push them out the bottom and let them fall to the floor. If the motor is assembled in the car, read my other post. NEVER USE THIS TOOL.
DO NOT EVER DO THIS! NEVER EVER! Pull the lifters up in the bore by hand until they stop and hold in place. Pull out the ones that slip out. Take the cam out. Make a cardboard or aluminum trough to slip in place of the cam. Push the ones that won't come up, down into the trough ONE AT A TIME. Fish them out with a magnet pickup tool. This way you don't damage the bores pulling a mushroomed lifter up, ruining the lifter bore.
Had this same engine in a 65 Impala SS while in HS. So cool! Pulled that cruiser surprisingly well!
And what are your plans for it when you do get it apart? It will need to be bored and what yr is it ? Is it a small journal or large journal motor ? If it's a large journal meaning 68 or newer it's really nothing but an underbored 350 and not really even worth fooling with you can't bore it to be a 350 and with so many actual 350 blocks available???? Now if it's a. Small journal engine that's a different story then your in the world of 283 302 and 327 engines and of course we all know how good they could be just being a small cu inch motor w a short stroke they had to be spun to the moon but when built right were amazing aka the dz. 302 for its unfortunately only 3 yr run it snapped many heads back lol so a small journal 327 can easily be configured in similar fashion w even better results .
@@GlennManchester it is a 1969 large journal motor..I also have a 1965 small journal 327 with the forged steel crank and camel hump heads…
@squarebodymob the 65 would be the one if you were going to throw money at it to give you the 327 rpms that they were known for if I'm not mistaken they have a four inch bore and just a hair shorter stroke than a 350 to get 327 a lot can be done w a big bore short stroke motor the large journal ones well you may as well just build a 350 is the way I understand it
@ I agree with you…
When I took the heads off I discovered that the motor has already been bored .060…so I was very disappointed about that…I did price how much it would cost to sleeve the cylinders and it is expensive…I was also told that I could actually bore the more to .080…not sure which direction I’m going with this motor yet..if nothing else at least I got a forged steel crank and a great set of heads from it…
Gettin their.
Still a ways to go but, congratulations.
@@RANDOMNATION907 it’s all fun…
I have also bought used engines to rebuild but the cost of this project will be high. It will need to go to machine shop for overbore and hone and new pistons, rings etc. Then you will need the heads done. You can buy a complete crate motor starting at around $2k. Not trying to discourage you but you might add up all it will need. I just bought a 283 on market place for $100. I am going to rebuild it for a early chevy nova. It would be cheaper to just buy a crate motor but I want to do this myself, expensive hobby.
@@ricksoldcargarage I totally understand what you’re saying..machine shops get big bucks these days…I guess the thrill of it all is building it yourself so you can be proud when the motor first fires up, hoping everything has been done correctly…
Yep, I am 68 and when I was a kid we used to rebuild these motors on the cheap and they would fire up and run. I have a small you tube channel and will probably do a video or two on the 283 for the fun of it. Good Luck with yours.
Longer vids would be good.
Bring that to me ill take it apart
They make lifter puller tool now
@@joseortega1114 I didn’t know that..
Hope she gets goin.
Thank you for the update.
Thanks for subscribing...
CONGRADULATIONS!!!!
Last of the good ones ,then they started screwing them up
Nice set of heads and also has a forged steel crank…
Has anyone ever used Evapo rust before? Does it really work?
When the end gaps are too small, the heat expands the rings, the gaps close up, and they have nowhere to go. So they force their way through the ring lands of the pistons. It's FAR better to have a little extra gap, than too little.
Yeah, that seems to be what everyone is saying...learn something new every day....
Ring land failure
Yes...I agree...
@@squarebodymob age...heat...oil...long live mighty mouse
Are your AutoMeter gauges mechanical, DIRECT REPLACEMENT FOR YOUR TRUCK, or universal fitment? I need a new speedo for my Dodge D150 1990. Do you think AutoMeter makes a gauge for my application. Also thinking of a GPS speedometer, instead of a mechanical one.
The altimeter gauges are mechanical…I have since taken them out..I’m going with factory replacements
@@squarebodymob Thankyou 👍👍
Very nice choice of shifter. Your truck is a real beauty, and really stands out. I have a Doge 1990 D150 regular cab with a eight foot bed, four speed manual shift on the floor. Thinking of installing a Hurst shifter in it in the future. Love the rims on your truck, really does enhance the overall look! What are the offsets of your rims from American Racing front and rear? Thinking these would really set off my two tone red and white Dodge.
Thanks 👍
What are the offsets of your rims? Love the look on your beautiful truck my friend. I have a Dodge 1990 D150, and after seeing those rims on your truck I was sold!
I don’t remember the offset on the rims…if I come across the original paperwork for them I will check it out and get back to you
Thank You👍👍
I love the look of those rims on your truck. I have a 1990Doge D150, and I am thinking your sizes front and rear would look amazing. My truck is not lowered and in pristine original condition, standard cab eight foot bed with a tonneau cover presently. How are these rims to mount up the appropriate tires?
Great choice of rims for your truck…rims mounted to tires with no problem
@@squarebodymob Very Cool, Thanks for your help!
Hello @SqarebodyMob we have a appreciation about Outlaw I wheels, look so nice but the question is what about rotors ventilation when down hill for example, thank you for your attention, be in touch.
I haven't had any issues with the rotors getting too hot..I know a lot of people love wheels with cooling holes in them..and I can understand that..but for this truck I just had to have the AR61 Outlaws...did you subscribe to the channel yet?
Your truck is beautiful and sounds bitching. Kinda like my own wife! Beautiful and always bitching 🤣🤣
Nice truck
Thank you..
Are the tires on the wrong side,the tread looks backwards ?
They’re directional..and yes I put them on the wrong side..I swapped the wheels over..
جمس
Cool video, I personally liked it.
Really nice truck you got there Joe! Very similar to the one my Dad had in Florida years ago. My niece has it now.
Thank you…I’m old school all the way…if you can, try to send me a picture of it and I’ll share it here on my channel
@@squarebodymob In case you didn't know, this is Dean. The truck is sunburnt from years in the Florida sun but my niece lowered it and drives it around in the summer months.
there have been a few trucks in that garage
needs a blower or turbos
hey i know this truck
Beautiful truck and wheel set up nice !
Thank you..Rachel..
How are the wheels holding up ?
They’re great rims..well worth the price..they’ll enhance the look of any vehicle..
@@squarebodymob thanks for the information brother!! I will most definitely order them for my b body caprice .
What kind of lug nuts did you use?
They look great, planning to get some for my Jeep.