Garrhett McKain
Garrhett McKain
  • 4
  • 4 572
Poulan Chainsaw rebuild
Poulan Chainsaw rebuild
มุมมอง: 31

วีดีโอ

Removal of 2010 Nissan Xterra SE 4x4 steering rack (and partial replacement)
มุมมอง 3.7Kปีที่แล้ว
Watch me remove the steering rack from my 2010 Nissan Xterra SE. While the replacement should be essentially the reverse of the removal, I did give a few tips to someone putting the rack back in as well. This should be the same for anyone with a stock 2nd gen(2005-2015) Xterra and similar year Nissan Pathfinders and Frontiers. I include a section of the video about tools needed, but also put a ...

ความคิดเห็น

  • @rayclaudio4141
    @rayclaudio4141 หลายเดือนก่อน

    My bolt that goes to that's steering shaft snapped lol

  • @scottcazelot4663
    @scottcazelot4663 2 หลายเดือนก่อน

    THANK YOU! Huge help!!!

  • @stanleykeith7863
    @stanleykeith7863 4 หลายเดือนก่อน

    You sux

  • @todrwilliams2871
    @todrwilliams2871 5 หลายเดือนก่อน

    Get to the work ......

  • @angelosolano9261
    @angelosolano9261 6 หลายเดือนก่อน

    Good video...thanks

  • @mitchellhines6200
    @mitchellhines6200 6 หลายเดือนก่อน

    just remembered american nissan might be a little different to australian nissan navara

  • @mitchellhines6200
    @mitchellhines6200 6 หลายเดือนก่อน

    I have just done one and found it easier to remove steering rack ends and pull out through bottom of car under engine sump no did not remove front diff either riggle a bit but does come out

    • @1966roadster
      @1966roadster 3 หลายเดือนก่อน

      Hey needing to replace my steering rack in my 08 xterra 4x4. You mentioned that you pulled it out the bottom instead of fishing it through the passenger side? Could you please go into some details about it? Thanks

  • @JimmyBoy87
    @JimmyBoy87 6 หลายเดือนก่อน

    Did you have to center that rack?

    • @garrhettmckain3120
      @garrhettmckain3120 6 หลายเดือนก่อน

      Yes I did. Actually I learned the hard way. I centered the rack, but left the steering wheel in the lock position, which Nissan put at 45 degrees off center. Had I more experience, I would have realized before too late. I ended up marking the position with the wheels centered and marking with the steering wheel centered, then disconnecting and reconnecting so that they matched. Back to your question, this rack did not specify so I centered it to make sure, some are centered out of box.

  • @raysno8367
    @raysno8367 7 หลายเดือนก่อน

    Do you think it would been easier to drop the diff

    • @garrhettmckain3120
      @garrhettmckain3120 7 หลายเดือนก่อน

      I haven't dropped the diff before so it's hard to say for sure. It wasn't particularly easy to get the rack out or put in so it very well could have been easier. I also was working with minimal equipment, contributing to my choice not to. In essence: if you're comfortable dropping the diff, probably would have been easier.

  • @danieltyutyunnik2584
    @danieltyutyunnik2584 9 หลายเดือนก่อน

    Doing this on 4 by 4 frontier wisn me luck