วีดีโอ

Padma is an alram o ly Onc epddm vale more than UL set value ( alaram relay operat (pddm>UL))

Yes

Need to enable time slots ..

Go to Par setup and press down in display show done Y change done N press ENT key ... its programming screen while press down key A.pri ... value show / ct sec should be constant

5.2456GWh / 5245.6MWh /5245600.00Kwh -- point 6 digit move Giga -Kilo

Its ok but i want to show that kwh reading in energy meter display not GWh

It's already available in my channel

Clear all the readings like ( intg,old,profil) and check meter Hrs ( date and time reading) still same error code occurred ( it's a calibration error ) replace new equielent meter.

Not possible

Hi ... you want programming modus parameter... or you need register mapping address

Sorry boss ... I don't know thelugu

For relising lock ... display in other than clr & set screen .. press Jo and down key same time ... display show Unlock then try now

@@powerblaster275 ok bro thanks 👍

Hi you want change frequency value..?

@@powerblaster275 mETER INSTALLED IN INDIA ,WE WANT INCREASE THE DECIMAL OF FREQUENCY .EXAMPLE 00.00 SHOUD BE AS 00.000

I think it's possible check meter programing parameter Display setting - scaling factor ( in case not available it can do only ION software only )

Share the meter model no

@@powerblaster275 In User manual of ION 8650 Page no.31 of 213 they have not mentioned for increase of Frequency decimal only Vol,Power and Current decimal can be increase.

Going to full setup and change dm prd -15 or 30

@@powerblaster275 during full-setup mode only the auxiliary supply must be connected to smart demand controller sir Full-setup should be completed before installing the EM3460 sir?

Please do one video on full setup if possible sir

Yes it's available only through software

Clear option for Em6438 meter through only software. Not possible to clr in key pad

Raise the service complaint and get new meter

Contact 9940109085 ( contact only office hours)

Import and export no need to do any setting...each phase kw value show+ve it's import value and kw shows -ve then it's export value

Thanks

As per discussion. i think your problem resolved

Not understanding your question... Pls call the service person from Schneider 9940109085

Contact 9940109085

Hi demand period TNEB can fix like 15 minutes or 30 minutes If you select 15 mint your demand interval is also 15 mint . Our meter also calculated the demand ( average of 15 mint kva is a reached demand ) Still your not clear .pls contact 9940109085 Schneider service team

👍🙏

Password.. 0000 . In case some one change pls share the serial number of meter

First set led in wh parameter and next set intg parameter then press down key display shows intg 0 ( till press down key ) KWh will show

@@powerblaster275 sir my ct ratio is 3200/5 ,I have set primary ct ratio 3200 but there is no parameter to feed secondary current, and I have connected resistance in auxiliary supply ,is it OK

The Dm model 3460 has obsolete, even schneider engineer has refused to give any support ,pls help me in programming

Old fwd and enter it's show old reseted reading

Both the reading need to match .pls check both reading match ( volt,Amps,pf ) then KWh also match ..Pls contact Schneider service person 9940109085

Yes this meter C tick licences meter ..it's show like this only ..

@@powerblaster275 sir your phone number please

Sorry for late reply... Em6438H , Pm1130H,old model em6438,Em6436 duel this meter you can read both EB & DG Both reading.kwh seperately

🙏🙏

Yes battery available for only energies microprocessor .. Energy prameter back

Already video available.... kindly refer Em3460 meter programming video

First set display in wh page then press right and left key Same time ... Display show few sec lock .. then display show always wh screen ( if not press any key 2-3mint default comes wh page )

@@powerblaster275 super g 5000 increment 😂😂👍👍👍👍👍🙏🙏🙏🙏🙏🙏 thank u

Thankyou...