- 36
- 9 688
Charles Giacomarra
เข้าร่วมเมื่อ 19 ก.พ. 2013
Onshape pg99 obj 4 work plane and project geometry
Onshape pg99 obj 4 work plane and project geometry
มุมมอง: 55
วีดีโอ
Onshape ied working drawing pg98 obj 1 & 2
มุมมอง 1152 หลายเดือนก่อน
Onshape ied working drawing pg98 obj 1 & 2
67 Camaro sbc Engine Install
มุมมอง 4934 ปีที่แล้ว
first gen camaro, install Blueprint reman 355 in 1967 RS Camaro, complete frame off restoration
First Gen Camaro EFI Fuel Lines
มุมมอง 1.3K4 ปีที่แล้ว
Update video progress on 67 Camaro complete frame off restoration. topics: new Blueprint motor, Tremec TKO 500 trans, CPP EFI fuel tank and braided PTFE lines. Fuel tank vent solution. Steering column restore discussion.
Isometric Sketching giacomarra
มุมมอง 1604 ปีที่แล้ว
Introduction to Isometric sketching for Technical Drawing classes
first gen Camaro rear axle shims and bushings
มุมมอง 5204 ปีที่แล้ว
first gen Camaro rear axle shims and bushings
Thanks for sharing the EFI tank venting solution! Had the same issue with my Tanks Inc EFI tank on my 67 Camaro .
Good to see my video was able to help you. Hopefully I will never have to see if the "rollover" vent checkvalve works. I really hated to have to buy a separate check valve and vent w/o the checkvalve. The folks at Tanks Inc would not cut me any break for the cost of these additional parts. BTW. I had to reuse my factory fuel tank fill pipe. The new pipe Tanks Inc. gave me did not have the gas pipe notches "clocked" properly. My Rally Sport gas cap "RS" was installed upside down. I told them about the problem, but they never replied back. Good luck.
is that an aftermarket tunnel?
No. The TKO500 fits the factory floor without any mods
Charlie, Great Job Sir. I hope you will come back and visit at school. :) Paul
Looking good
Awesome video Mr. G! Fun to see what PHS was up to back a few years ago, now that I’m part of the community. -Pratheek
I really like your vent line solution!
Awesome video. I have a Butternut Yellow 69 as well.
Hi Andy, thanks for watching. I figure I'll keep it Butternut Yellow, that will be one of the few original things left since it started out as a 6cyl 3 speed manual car. Here's a link to my video on the new fuel tank, lines and vent: th-cam.com/video/AbQcmW8YmhM/w-d-xo.html
@@charlesgiacomarra531 Same with my car. It was a 350 car with a 4 speed Saginaw. It now has a Vortec, M22, 12 bolt being built, and some other goodies. I’m on IG: 40code69.
Hey Mr. G! Great job 😃👍🏽
Thanks Jaden. It's nice to get some positive feedback. Enjoy the rest of the weekend.
Great video Dad very informative! I'll be using all your fuel line supplies.
Thanks for sharing. Good information in your comments. God Bless
Great project!
Nice project. Thanks for sharing your knowledge. Subscribed to your channel. Hope you post more videos. It would be a big help to build my first generation.
Thanks for the feedback. I hope to put out a video covering how I handled the fuel tank vent hose and running the braided fuel lines for a Holley Sniper EFI. First I must recover from a fractured pelvis. Ugh.
@@charlesgiacomarra531 Sorry to hear that sir. Get well soon and keep on wrenching! Heard plenty of good reviews with that set up. Cant wait.
Cool!!!
You should really make your human feeding ramp wider at the top. The current size is silly
Thats some cool ish.. Nice job guys! P-Way Represent!
Nice work, everyone. The thing shoots fast, doesn't it?