วีดีโอ

Watched the video hoping you caught me

Thank you I’m making my own soon

The lights may flicker if light is on same circuit as fridge or freezer.. try putting on dedicated circuit.. motors do draw a lot though if your maxing out the system - you may need bigger inverter to handle the surge to avoid the flicker.... i have the same single unit with single phase 120.. we only get a flicker when portable ac comes on cause it shares wall outlet shares circuit with the plug in lamp in living room.. thanks for sharing your setup.. we use pylon protocol to get an accurate battery read.. you need a battery with a smart bms that has a communication protocol to get it to work properly.. otherwise use the user setting and setup the correct charging settings for your type of battery.. otherwise you may damage them or worse.. what heat pump / mini split do you use - im thinking of trying one as well

You've got to show this in action..

Nice work, but I would have started with cardboard to create a template for those gauges.

Hell I would buy one from you

I appreciate the review and look inside, so thank you. Hard to believe they mis-programmed the low temp cutoff 🤦‍♂️ I guess the Bluetooth feature is pretty much as good as a shunt? If so, that's pretty cool. Also impressed that it works through the freezer lid/walls.

A little tip for bending copper tube, if you fill it with water then freeze it it will give you smoother bends. I learned this from watching how they make brass instruments.

Your sides aren't filled, that would maybe get you to 100lbs.

Thanks for the review I was interested in this cheap battery and you answered all my questions. Good job. Would appreciate some cutting of the charging and discharging we don't really need to see that, just the results. Thanks again.

Wow I really like that very nicely done. I have a 77 economy with a factory front loader. I have been thinking about repowering it because the old Kohler on it is very tired.

looks great. thanks for sharing.

Yes I have same issue with my twin LV6548 in 120/240 v running 18 months . Yes, Led lights flicker with a higher load draw like a coffee maker or simular loads. I just bought a new NKH low frequency inverter 10 kw to change over soon. I monitor with solar assistant, no internet connection. Biggest LV6548 complaint is 250 v maximum PV volt input. These were good units at the time but equipment has changed for the better over the years. Thanks for sharing your setup.

These high frequency inverters are far too noisy and they don't offer any galvanic isolation for safety. They also offer a far poorer surge capacity and a shorter life expectancy than real inverters that use longer lasting, higher surge, low frequency, transformer based inverters.

what's the power factor on your fridge and freezer? if they've got a restive start, resistive run compressor, they usually have only .5 to .6, which is likely going to stress out the inverter as it's seeing effectively twice the amperage draw from the reactive power being so many degrees behind the sinewave.

If there is a coupon on an item on Amazon after you place an order sometimes i have been able to place another order. Ir you could get someone else to place orders for you with you credit card if you trust them a lot.

The fridge and freezer on the same leg, right? Do you have a bad, loose ground?

nice project! if its still running how much kWh it makes per month? and do u use/store that energy somewhere?

Looks great, that is a big improvement. I'm going to PU my new mini digger next week as well.

Appreciate the review. Going to buy one of these and was curios about it.

awesome work

I love the rivet trick

Would a solor panel to the top of the canopy be beneficial? Possibly used as a battery charger or to run another fan?

Wow that was easy! Are you going to fix it and flip it? seems a bit new fir your collection lol

Nice! I really hope to make it back out there again at some point across the next couple years! Also love the little Nelson?? engine you brought! I want to find one like that some day!

You know I made a wing turbine were one of those hover board motors for 12 V system and I seen that thing pulled out 16 to 20 amps

Thanks for filming. Looks fun.

Unfortunately never been there looks like a fun event to attend

looks like a great event

Hello- I really enjoy your modifications. I was wondering if you had a issue with the blade lift height ? My dozer blade only lifts a few inches above the ground, limiting my travel, especially climbing up ramps. I thought your engineering brain may have a idea to allow the blade to raise higher. Maybe cut and raise the blade brackets? Thanks AJ from North California.

How much power can you get off a wheel?

Looks like you could reverse the connectors and have 4 positions of the lifting points

Good videos. Did that much counter weight make much of a difference? I need to add some counter weight to mine. Curious about how much weight it needs. Thanks for the ideas.

I have an old 2 stroke lauson I need some help wit setting the point or if n where can I get a new coil or parts

Nice Job!

Want to double your money? ha ha ha,great buy! If I remember (Gray matter is 80 years old ) right alternator is way underrated .Keep on Keeping on. Steve AKA Delco 32volt

I have two of these old things also. I am really anxious to see how you get this thing running.Mine do not have electric start. You have a really great model.

Do you have a channel on a different platform then YT?

Very cool!

I've quickly learned that the limiting factor is the speed of the ex, so I try to get my tractor as close to the action as possible to minimize the travel time expected of the ex. They sure are handy where you can fit them and their power to size ratio is somewhat frightening.

Htrc coolers always work as a jet turbine 🤦‍♂️ Damn, their chargers are not bad, I would use them, but it is impossible to use them inside the house with lifepo4. The sound is awfull. They suite only in garage.

No genera amperes y se frena

You need to address the hoses. There is often enough slack in them to get pulled into the blade. Also, they can snag on limbs, fence posts or other obstructions. A good first step would be to add a 90 or 45 degree ell at the motor connections. Just my 2 cents.

Great stuff ! Can you tell me what the specs in the hydraulic motor are ? Thanks

Very nice upgrade .👍🏻🇺🇸

Skill

Hi man, Nice video. I have the same supply and it was working very nicely. Today I tried to turn it on, and after plugging in the power, I was just selecting the voltage, and the display just turned off after 2,3 seconds of power up. I hadn't even turned on the output. I tried replugging it, but it's not turning on now. I tried opening it up and I see that the bridge rectifier IC is giving DC output, but I can't diagnose it further. It would be really great if you can provide some help on how I can diagnose what's wrong. All components look brand new and there's no burnt component and no burning smell. Thanks, Divyanshu

there's some unusual stuff there.

Wow is that a really cool project. I didn't even know they made those. Truly a great find.

New subscriber here. That is a really well made tractor...I came over from Mike Fiesta's channel and he spoke highly of you and now I see why!! I am going to tell everyone I think who would be interested. I am about to start a channel with the build of a 1928 Morgan/MG special hillclimb racer. I am in Pennsylvania and am glad I stopped by..