วีดีโอ

Un outil qui demande une très grande refonte… Rien de tel que d’investir sur un Kd Max ( keydyi) ou xhorse.

It didn’t let me do it, it says doesn’t support my Cas3+ module

Are You using the OBD port?

you have to use there key to copy

Why they market a device that cannot be used (under development) A car factory would sell a car without an engine, and then later send it to the customer. Lots of promises since May and no change. Chip copying is impossible!! Huge scam.

Does Km100 program keys for the 2010 BMW X5?

is it possible to download IMMO PLUS SOFTWARE to other device( android tablet ) ? because i need bigger screen.

Funktioniert das auf Android und iOS ? Wo kann ich den link her bekommen?

Hilo bro Immo plus how many have reset? Do you know between immo plus vs launch3s? Which one is better do you know?

id 48 copies?

Your not doing it properly

Jlink V8 or V9 ?

ola escrito novo. poderia me explicar como funciona? obrigado

Hi, nice video thank you. Did you do that with the IMMO Plus and MCU3 with Xprog3? Can the IMMO PLUS also do cloning of the 7G TCU?

Pks no talking

Same totally useless junk, not even plug to solder direct. Din plug to micro connector, but no micro connector to bare wires to make solder connection. Key reader / transponder reader function only. My xtool scan tool does more then this unit.

hope cgdi solves what they have promised, otherwise it's a waste of money

I got mine today and have tried a few things and it feels like a totally useless toy, reads frequency and chip but can't do anything totally disappointing

TODAY IS THE FIRST TIME IUSED IT , IT ONLY READS REMOTES IT DOES NOT PROGRAM ANYTHING. IT IS UNCAPABLE TO PROGRAM A BASIC NISSAN REMOTE MUCH LESS ANY VEHICLE THAT REQUIRES IMMO INTERFACE DO NOT WASTE YOUR MONEY UNTIL ALL ISSUES ARE RESOLVED

I has to program new key cards to Megane 2005 . I have Launch CRP919EBT Elite . Can be cards added without pin

con esta se puede trabajar con camiones

Can it be done with Launcher X431 ?

This car has CAS3+, and you were adding a 2nd key while you have a working key? Can KM100 do all keys lost with CAS3+ ?

It would've been good if I could actually read the screen on the Autel device instead of getting seasick

Здравейте, може ли на thinkdiag 2 да инсталирате prodiag?

Where to get the blank keys? Does it need a certain tyre or will any AliExpress copy work?

Contacto 🤔

Hi I did bmw1 series from cas3++ and dme aunch Immo elite with xprog 3 I read isn from DME but when putting isn says wrong ant advice please

Is thinkdiag 2 a VCI by default ? It doesn’t have passthru function, right ? Only CAN FD

For 8041B6 8041D5, I think change height throw sensor and or check cable for LWR wiring loom for any breaks.

what is the procedure for this tool to replace an ecu with new one but you have burnt or unreadable old ecu from the car your working on?

Hi how to get isn akl

pls make a video with IMMO PLUS do diagnostics, actuation test, and special functions per car brand.

please make a video of IMMO PLUS do diagnostic , actuation test and special functions under car brands....

Hi how to read isn to do all lost keys?

Shouldn't you restore the data that you backup from the first dme to the new one ?

После каких манипуляций удалось получить пин-код ?

I need help I have immo plus I want to learn about using the xprog3 and procedure for programming some vehicles If can get videos or maybe on pendrive or something i will pay Iam in Ghana Waiting for your response

Post how to program it... Renew is a piece of cake.

Thank you.Why didn’t you immediately write the full data of the original transmission into the new one via the imoprog function launch? Or do you not have the original file?

😂😂😂😂😂😂😂😂😂😂😂😂😂

👍👍

Is this online coding?

Is this cloning ore reprogramming the key?learning the key ?

"promo sm"

Where can be purchased that autel?

Can launch repair a corrupted data on a frm?

Hello, how did you get access to the main tablet screen? My one won’t let me

Do you need a battery maintainer?

Merci mohandis