OMG No! No! that sleeve is so loose it will not be able to dissipate its heat to the cylinder for cooling, and the worst is that sleeve will "Walk" and push out the head gasket. please nobody do this its a hack butcher job. great installation information can be had from either LA Sleeve or my boys at Advanced sleeve around the corner.
This is very poor job of re-sleeving a cylinder head, the actual process is very different bcz it involves heating the cylinder and shrinking the sleeve with cold it takes a precise amount of calculation and almost ration of heat and cold for re sleeving cylinder and perform effectively.
Nooooooo You must warm the cilynder and male the sleeve col. Than it will go inside with free play to align. In just 5 second than you align the port.. Why this people don t sue the head...
Sleeve installation kay baad kesi performance hoti hy RX115 ys 135 ki. Kuch loog kehtay hein 2stroke mein sleeve successful nahi rehti pick aur power mein faraq aajata hy. Aur piston bhi seize hota hy
Merey pass RX115 ka engine hy uss mein pehlay say sleeve lagi hui hy. Aur piston 50 number ka laga hua hy. Koi pleaee guide me which maximum size piston i can install in my engine for maximum power. I need maximum horse power Mera whatsapp +92-333-4868797
Please share contact number
Murder done
Price
Not a proper work.. Old process this is
No perfection 😂😂
How much it does cost
Sleev cost 1500
@@surajliferocks I want to put new sleeve on my 5speed block It will be alright?
It's not successful
Contact number address please
I feel it should have hydraulically been pressed instead of hammering.
Number bron
🚮 Total waste job cleanly recorded on cam 🤣
Poor Sleev Work Pasting With Araldite
Your location your phone number send me
bro ethu avlo price bro sollunga en bike ku change pannanum
3800
Thank you 💛
Once sleev is last over size what's next Can i use that block or not
not
Tumhara number bhai
OMG No! No! that sleeve is so loose it will not be able to dissipate its heat to the cylinder for cooling, and the worst is that sleeve will "Walk" and push out the head gasket. please nobody do this its a hack butcher job. great installation information can be had from either LA Sleeve or my boys at Advanced sleeve around the corner.
Suzuki shaolin cyinder port pannuma ?
No sir sleeve not available ...
Bro Yamaha RX100 bike la sleved and unsleved yaepadi kandu pudikaradhu konjam busy. Very urgent.
Bore ulla porting pannirukanu pakanum bro
Successful hota hai kya ye sleeve rx135 mei
Ha bhai sahi tarike se hoga to acha kam karta hai...original jaisa to nahi lekin dum hota hai
This is very poor job of re-sleeving a cylinder head, the actual process is very different bcz it involves heating the cylinder and shrinking the sleeve with cold it takes a precise amount of calculation and almost ration of heat and cold for re sleeving cylinder and perform effectively.
Absolutely
Nooooooo You must warm the cilynder and male the sleeve col. Than it will go inside with free play to align. In just 5 second than you align the port.. Why this people don t sue the head...
Super
சூப்பர் bro
Send Your contact NO. I have Yamaha RX 135 I want to install sleeve
100 Persent saaf kam
Ahh the good old swing press
number
Wrong method.fitment also loose
Send me your number
Yamaha new bike 2002 chahiye kallu
Where is this shop?
9545464399 call me
sir apka contact number milega
Bhaiya apna shop ka address batao
എന്ത് തേങ്ങാ ആണ് ചെയ്യുന്നേ ഇങ്ങനെ ആണോ sleeve ചെയ്യുന്നേ. അപ്പോൾ കുറെ കാലം കിടക്കും.
Evolavu Aachi bro How much cost bro
Ggg
Nice work
Sleeve installation kay baad kesi performance hoti hy RX115 ys 135 ki. Kuch loog kehtay hein 2stroke mein sleeve successful nahi rehti pick aur power mein faraq aajata hy. Aur piston bhi seize hota hy
Port matching ho toh kuch problem nahi hoti hai
@@rishigovekar1419 right
@@rishigovekar1419yes a 💯 right
Merey pass RX115 ka engine hy uss mein pehlay say sleeve lagi hui hy. Aur piston 50 number ka laga hua hy. Koi pleaee guide me which maximum size piston i can install in my engine for maximum power. I need maximum horse power Mera whatsapp +92-333-4868797
Tell us what's standard size and sleeve size
0.25 mm bro
@@Deepakgs-bu6mx if in micrometre it says 50.23mm then till what size ull do honing
@@akibkumbari3790 the next size will be 0.75
@@Deepakgs-bu6mx bhai agar 50 mm ka block size hai n oversize piston 0.25mm ka hai to aap isko kitta boring n honing karoge
@@akibkumbari3790 bhai standard size hai 0.25 agar honing karoge toh next piston size apko market mai 0.50 hoga
Contact number bro
Full video post pannu ga bro
Ekdum badiya bro 👌👌👍
Bro can you tell me what is the procedure of removing an old sleeve
heat it up in a oven and carefully tap it out with a block of wood