วีดีโอ

Thank you

Does the heat unstick the leather from the wood?

こんにちは、コチラのシャープナー 日本で販売していますか又販売元から日本までシャープナーと送料で価格を教えてください。です

I’ve always wondered about getting a burr and why I never see one. I never found a good answer so thanks. This was incredibly helpful for me.

You know.........Some wooden paint stirring sticks cut to size, a glue stick, and a piece of non corrugated cardboard will absolutely do the exact same thing...............

Why............................A piece of flat non corrugated cardboard even with no stropping works every bit as well as a leather strop. Use a few times, throw it away. No maintenance.

hello, is the sharpener you are using self-made?」

Where did you get those 2 long skinny strops on the table?

Where can I buy the same sharpener?

Well done, Brian. I'm just about to order up my initial TSPROF kit. These sharpening systems seem to be incredibly well engineered & manufactured. Very, very impressive tool. Are you as satisfied now after having spent some time with yours? Thanks for the presentation...

Hi, The angled guide rod make the convex edge by it self, you do not need foam. It works better, and with higher precision with a normal diamond sharpener. If you use a 6 mm thick sharpener the protractir shows the correct degrees when you have 28 cm between the cutting edge and the pivot point. This means that you adjust Chef for different blade width. For eveey thumb you use on the sharpener length you get 1 degree sphere = 3 thumb length give 3 degrees convex sphere. Thomas

How do you compare the Edgepal Chef to the TSPROF KO2?

You roll your blade tip off the edge really hard. That’s going to ruin your tip over time. Also, blade with large belly like that really need to be rolled away from the stone as you go around or you’ll end up with a thickened blade tip and shortened blade.

Just a long-winded observation 🙂: the bent rod is for convexing; it will work by itself, making the foam-backed sandpaper redundant. If anything, the give in the sharpener will, first, go against your ability to control the degrees of the convexing precisely (if you care about it), as well as force you to go in a single direction when sharpening, instead of back and forth. With a stone, you wouldn't worry about accidentally cutting the sandpaper (and, of course, ruining your edge in the process). Still, some stop-collars may save even your sandpaper and your edge you worked hard for, methinks.

I wish you were doing a different camera angle. The overtop you can’t see much of anything.

Nicely done video, liked the finger hold tip. Tanks!

Hello. I have the ko2 version of this without the case. They want to much for their case an im looking for one elsewhere. I dont suppose you could post the dimensions of that case.

ผลิตจากประเทศอะไรครับ.

You are slamming the tip of the knife edge down on the table after every stroke? How are you going to sharpen the tip doing that?

I needed to see the yellow up close

What's the difference between the green and white compound?

Nice video, but volume is very low-difficult to hear, even with ear buds and/or hearing aids.

Thank you for the detailed instructions. I just ordered the TSPROF Kadet sharpener. They are supposed to start shipping on the 15th of April if you preorder. If I would have seen your video then I probably would have spent my Stimulus money on this system too. Great system, good luck sharpening knives.

Where did you get this? I didn’t see a link. Thanks.

What are the cleaning things you use on ceramic rods I would like to buy some

The video has no volume. Why?

Sandplex?

To clean your stones, it sounds like you're saying "Samplex." what is the correct spelling? Thank you.....

Honest guy here, appreciate your views. Thanks for posting!

Going to round your tip off.

What does the WD 40 do for the stop? can i put that on top of a compound that is already on the strop?

Gonna round your tip :(

Why aren’t you using the flat edge at the beginning? Do you use the triangle tip just to repair the edge before sharpening?

great video! thankyou for that

Will kme stones fit this?

Thanks for the video. You mentioned that you can fit different size stones. But are you tied to proprietary stones that are made by or for TSPROF only? If not, do you know what other stone manufactures stones you can go with?

Next video?

I like your comment I could be saying that cause I spent over $700. Nice video. I just got this drill sharpener for my Wen machine. Have not had a chance to use it yet bet I am very impressed with the weight and quality of this jig.

It's my understanding that the guide bar and the stone surface need to be squared. The surface and the side of the stone squareness is irrelevant. When you use the stone truing tool the diamond cuts the stone to be parallel to the guide bar.

Thank you very much for the nice review!!!

so the secret to getting a mirror polish with a sharpmaker is to use a strop

where to buy the diamond ones

Is that a TS Prof guided sharpener?

i am considering the edge pal for my next sharpener.....thanks........... <")))))<>(

Thanks for the video I have a blur and just bought it and the sharpmaker I got the uf stone's separate but not the diamond ones should I use the 30 degree like u or use just the 40? Also being it has that slight recurve should I use the flat part of the stones and the edge part or only one or the other??? I'm a complete novice when it comes to sharpening. Also not sure if it matters but my blur is the s30v veraion.

Thnk you, you have sold me on this system, ill have to make a jig for my milling bits.

Hi. In my country there is no Compund, what can I use instead of Compund?

Thanks for that, useful video.

You fast forward through the journey of the sharpening which is what newcomers need in order to figure out the process itself....

Arguably not enough green compound LOL