- 16
- 5 480
Robert Patton
เข้าร่วมเมื่อ 20 ก.ย. 2013
2007 Pt Cruiser verifying voltage on CAN B Bus wires
2007 Pt Cruiser verifying voltage on CAN B Bus wires
มุมมอง: 94
วีดีโอ
2007 Pt Cruiser Can Bus test At data link and TIPM
มุมมอง 261ปีที่แล้ว
2007 Pt Cruiser Can Bus test At data link and TIPM
2007 Pt Cruiser testing negative signal coming from PCM
มุมมอง 53ปีที่แล้ว
2007 Pt Cruiser testing negative signal coming from PCM
2007 Pt Cruiser Testing fuel injector circuit from the ASD relay
มุมมอง 1.7Kปีที่แล้ว
2007 Pt Cruiser Testing fuel injector circuit from the ASD relay
2007 Pt Cruiser Fuel injector test No power or control signal
มุมมอง 380ปีที่แล้ว
2007 Pt Cruiser Fuel injector test No power or control signal
2007 Pt Cruiser fuel pump and injector test.
มุมมอง 867ปีที่แล้ว
2007 Pt Cruiser fuel pump and injector test.
2007 Pt Cruiser It's alive! But still has problems.
มุมมอง 82ปีที่แล้ว
2007 Pt Cruiser It's alive! But still has problems.
2007 Pt Cruiser checking resistance On pin14 c5 on TIPM
มุมมอง 69ปีที่แล้ว
2007 Pt Cruiser checking resistance On pin14 c5 on TIPM
2007 pt cruiser changed motor no Crank Condition Help!!!!
มุมมอง 81ปีที่แล้ว
I am stumped. I can not figure this out. Pin 8 on the c10 connector has no power. Why? Is it fused? And the relay is not clicking and it should be. It has a signal from the ignition it has a - signal from the pcm. So It should at least click. So If any one has any idea please let me know In the comments below.
Homemade maple syrup Evaporator father and son-(part2)
มุมมอง 514 ปีที่แล้ว
Not much to say about this one. We have two 55 gallon drums to boil down. It will take a while.
Homemade Maple Syrup Evaporator-Father and son-(part1)
มุมมอง 1284 ปีที่แล้ว
this is a homemade maple syrup boiler. It is made from a 250 gallon fuel oil tank. It took me about 4 months to make. I took my time. I was in no hurry. it still needs a few things like i am going to build a way to slide the pan off it. When the syrup is done. And I am going to have to build a warming pan for it. Those two little stemming pans don't work very good. So i am going to build a pan ...
Mine just died lmao it doesn’t even turn on any lights. Battery looks cooked though I hope it’s just the battery. If not I’m getting obliterated because I gotta buy alternator and pcm
Except my security little red dot on dash stays on the whole time
07 pt limited 2.4L turbo ... replaced tipm and pcm and now I'm having same issue
Maybe it’s the wire harness to the pcm or bad battery. Mine has a cheap battery and scan tool says low power to pcm
Where did you connect the gauge to fuel line?
This is exactly what’s happening to me, I’ve replaced the starter, battery, and temp sensor. No luck. Going to try the ignition switch
Was it the ignition switch?
Could be pcm too
Let me know when you find out. My car started do the same thing today
Let me know when you find out. My car started do the same thing today
Same thing happening to mine
I'm not heading a click, so Imagine that your starter is being actuated by the turn of your key.
So if you were to remote switch the starter would spark and injectors still function ?? ( key in run position) .