วีดีโอ

Long press lang po. ty

If you have Logitech devices connected to your PC... Yes, you need "LOGI" to configure your devices. Otherwise, if you don't have these devices... You don't need "LOGI" to turn off "CAPS LOCK" notification. Because only Logitech's software or "LOGI" turns on this feature once you automatically install "LOGI", when you connect your devices. Thanks.

You can tune every string to pitch without worrying of popping it. The real headache is keeping everything in tune. Sometimes if the strings were not properly "pre-stretched", it can take about a week to stabilize newly installed classical strings. You can try to hold each string between your thumb and index finger and gently pull on it gradually for the entire length of the string before tightening it. Thanks!

When you plug in the microwave, right after the beep, press "START," and it will start, initially set at max power of "750" for 30 secs. Use the up and down arrows to change the time with increments of 10 secs. Or press "START" again to add "30" secs. That's how I use it to heat food. Thanks. th-cam.com/video/CIQk5b8cNRk/w-d-xo.html

@@kenztonnaturevideos Thanks!

SJCAM ZONE

@@ImAChickenNuggetSandwich The reset cable of the case into the reset slot of the RGB controller box. Thanks!

i get that but there is just an end from where the button is down to the end of the wite

wire

and there is no where for it to go i just don’t understand it

@@ImAChickenNuggetSandwich Try watchung the complete version of the video. th-cam.com/video/XuEGPDanMLY/w-d-xo.htmlsi=e_xkqVz2PK4tOHh7. Thanks.

@@JeadanPersona Maraming salamat po! Ang alam ko pong max capacity nito is only 128gb SD card. Ty po sa comment.

Yes, pretty close. But we were there two weeks before the earthquake.

Updated na po yung mga links para sa Control Switch. Nakahanap na po ako ng kaparehas. TY po!

@@tedtedhk yes

Spark plug - Torch D7RTC - NGK DPR7EA9,DPR7EA-9,DPR7EAGP-9,DPR7EAIX-9,DPR7EIX9,D8EA,DR8EA,DR8EGP,DR8EIX,DPR8EIX-9 - Bosch XR7DC - Denso X22EPR-U9,X22EPR-ZU9,IX22B - Champion RA8YC Any brand kahit ordinary or iridium,same size sa tmx at xr. Eto po sabi ni google... “B” indicates a 14 mm x 1.25 pitch size, “D” indicates a 12 mm x 1.25 size and “C” indicates a 10 mm x 1.0 size. The letter “J” indicates a 12 mm x 1.25 size with two ground electrodes. The “P” indicates a projected tip spark plug design that moves the spark deeper into the combustion chamber. Pero di ko po sure sir kung swak sya. Sensya na po. Eto po yung binili ko dati na sinoli ko po kasi di kasya. CR9EIX

Nasa listahan ng compatible replacements po yung nabili nyo na DPR7EIX-9. So, malamang swak po yan. Yun pong kasama sa tools na pang-tanggal ng spark-plug ay di po kasya. Hanap ka nalang po ng ibang size nun. Hila lang rubber luwag ng counterclockwise po. Salamat

@@WhooshyRider Yung dulo po ng DPR7EIX hindi po siya matulis hindi katulad nung stock na torch D7RTC

@@lucasmiranda2572 Oonga no. makapal at walang thread. Nasubukan mo na sir yung DPR7EIX/ Swak kaya sa CR152? Maraming salamat po sa info sir!

@@WhooshyRider Hindi pa nga boss eh hindi ko mapasok sa plug cap masyado mataba parang mali nabili hahaha

Tried it just now. I don't see any options for utilizing the FOV setting using the built-in camera APP in Windows 10. So, I guess the answer is "NO.". And there's also no way you can use the SJCAM APP in your phone to change settings in WEBCAM mode, for you cannot connect to it while using it as a WEBCAM. Thanks for the comment.

Yes po! TY

@ idol bakit po kaya yung sakin ayaw? dapat po naka neutral lang siya kapag po nasa primera ka tas piniga mo clutch ayaw po gumana push start

@@bealoudesrieevangelista5548 Hindi po kumakagat yung switch nyo po sa clutch lever. Silipin nyo lang po baka kalas yung cable nya. Kung me contact naman po baka deffective na po yung clutch lever switch. TY po. RS po lagi!

@@WhooshyRider ayan po ba yung switch sa left na parang katulad ng nasa right? baka nga po defective lang may contact naman po

@@bealoudesrieevangelista5548 tama po 2 bakal na flat na terminal po yun tapos me cable pong nakakabit. yung sa kaliwa po ay clutch safety switch. yung sa kanan ay para brake lights po. try nyo muna pong linisin o bugahan ng langis o WD40, pag ayaw pa din po ay medyo bend nyo lang po ng kaunti yung flat na bakal na terminal. pero alalay lang po. ty ulit

Paano pong extension sir? Yung stock na side mirror po naka rekta lang po yun sa mga levers. Unscrew lang po. magkaiba lang po ata ang direksyon ng pagluwag at pag sikip. TY po sa comment. RS po lagi.

@@Iameverywhere6969 Thanks!

When you turn on the time stamp, the current date and time will automatically sync to your phone. th-cam.com/video/v-itPCSEyEY/w-d-xo.html Thanks.

Depende po sa madalas mong dinadaanan o kung mdalas mo pong ginagamit. Ako sinisilip ko lang po pag medyo maitim na linis na po. ty po sa comment. RS po lagi.

Maybe about 10ft or less with noticeable lag. I'm not really sure. Because I only use it for framing. Meaning my phone is often less than 3ft from the camera. Thanks.

@@WhooshyRider Thank you!

Yung lever ba po hanap nyo? TY

The wiring diagram for a 3-wire 220V welder plug will typically consist of three wires: a black, a white, and a green wire. The black wire is the hot wire, the white wire is the neutral wire, and the green wire is the ground wire. The purpose of the ground wire is to trip the breaker in the event of fault current safely. If the ground wire is not connected correctly or is missing, it will cause a severe electric shock to the person and harm the building. We therefore connect the ground wires to anything that could potentially become a potential path for electricity to leave its circuit, such as the metal pipes, the metal plates, the light switches, and the outlets of their boxes. Example: I connect the ground wire of my washing machine to a nail hammered through a concrete floor. With this microwave, I left it disconnected, but not advisable. Thanks!