วีดีโอ

using cellotape or something that make censor cant read at buttom dji neo and make sure that censor are closed.. neo cant read from the censor to take off to water

Can you exercise videos in different speeds, like 1.5 or 2.0 ?

Worked the first time and then stopped almost immediately.

bye bye😂

Sir thanks a lot for the video but i have known the cutoff fuse is 150c, please what's the exact amp?

I would never try to use the auto modes for that

awesome fish show

You are the man!!!!!

Thx, great to know

Great! Helped me out with an Eonon stereo that was driving me nuts!

Worked 100% Thank you.

Thank you, I had the same issue and this tip made the trick. I was about to take everything apart 👌🏽

То же самое было с моим первым DJI Neo там слабый сенсор который видет дно как поверхность и поэтому садится

Where to get that thermo fuse ? can you pass some link

Thank you! It worked perfectly at the first attempt

I would have jumped after it

LOve that heater installed horizontally with very fancy display, i love the floating plants

I tried the instructions but it didn’t work for me. The problem I have is that the camera works fine during the day, but at night, it shows no signal.

Nice casing and phone bro!

thank you. great video.

Thanks for the video, I been trying to figure out how to shuffle play all year lol 😂

Dude, you are an absolute legend! I was sitting in my car for two hours measuring everything again and again trying out different stuff before I came across your video. Now it works! Thank you so much!

the problem with mazdas from 2014 models, is that the buttons for voice commands and calls controls (open/close) can't be mapped cause they are not under fkey1 and fkey2 but they go straight to the bluetooth console ... and I never found a canbus that was able to intercept and translate that

THNK YOU SO MUCH!!!!

Thank you so very much .. this was exactly what I needed. Fixed my issue. Cheers.

Bro you just saved another life here in ARG. Thank you very much!!

Super helpful👍🏽

This is exactly what happened with my first Neo, lesson learned...the hard way hahaha

Thanks for the video ,un boxing one now.

TS9 fm set process

Thank you, although it is a different device, you opened my mind and I have reset it, saving me the trouble of repairing and buying equipment.

Is your front table (the one that says “pro series”) kinda wonky when it’s extended out? I tried fixing this on mine with zero luck.

Thank you ! ❤

Thank you very much .....

Wow this scooter is amazing compared to the gotrax xr I have. I’m still thankful tho only thing I wish I could ride in the rain.. 🌧️ safe riding everyone 😊

THANK YOU SO MUCH!!!! I have been searching the solution with the same 'no signal' problem for 2 whole days. There are so many noisy information on the net though.

Bonjour j ai cherché pendant des jours sans solution et grace a votre vidéo j ai réussi je vous remercie de votre partage merci merci merci

Great gadgets!!!Please would you educate us on how much heating is needed in an an aquarium so we can compare which gadget does the job better this one looks good though

Vinegar will not descale anything you would have to leave it in there for a long time.For the acid to get through it

Hi did you ever get water ingress? I just bought a used ghost scooter and curious how safe to run in the rain

What do I do if the faceplate doesn’t go back on

DJI suggest not to fly it over water at low altitude and never in auto mode.

I would hope that you could drive from Van to Ab and not wind up with cracked brake pads. How many times did you stop on this long hiway run?

10 1/2 minutes and the first wheel is finally off.

I'm sorry buddy but we're 6 minutes into the video and you haven't done anything brake related! Getting to the point quickly is what we appreciate, so next video please bear that in mind.

Great video, just wanted to know how to remove battery to screw the kick stand, but found this so informative. Was scared to have battery problems down the line and looks not too hard to repair! How did you add the lights, would love to do this mod, I always ride at night?

Imam isti problem,pokusat cu sutra s tom varijantom mozda upali 😉

Hello how i find this gasket for 206 fluval

I seems fake but I will give it a try

I changed the brake pads on my Ford Escape last week and it was painful and horrorfull. For starters, you need a #7 hex wrench for one of the pin bolts of the caliper and a #9 hex wrench for the other one. WHY? Why in God's name use 2 different sizes for the pins? I had my car disassembled and had to take a city bus to the store to try and buy a #9 hex allen wrench which none of the hardware stores sold. Curiously, none of of my hex allen wrench sets had #9, they all had that one missing from the factory. I had to borrow one from a mechanic to continue doing the work. Also I gave up trying to put that silver brace that you can see at 15:30 in the video, I had to put the old one because none of the 2 of them fit, alas watching your video I see that you have to FORCE it in. Another problem I had was that the pin bolts were hard to loosen up. I had to heat it up with the torch to loosen it, and it was not a good idea because I could smell burnt rubber. Anyways, I finally succeeded, now I'm going to attempt to change my brake drums in the rear which seems an even bigger challenge. BTW buddy excellent clear and instructional video, word of advice, next time use a little chair to sit on it while you do this, that's what I did. no need to be on your knees. I used my daughter's little chair LOL