วีดีโอ

Thank you, needed to know how to take the top cover off. my button had some issues and basically failed due to the dumb idea of putting a rubber gasket that wears out over time so I just stuck some thick double stick tape in there and it should last now until I need new tape

Merci beaucoup, j'ai reussi sauvé ma tonndeuse. 4,5€ les batteries versus 50€ une nouvelle. Le choix est vite et clair. Thanks

Works to me

How to calculate the time. As per set value and shown value.

It is very good explained in the video thanks

Useful video but there is a cut where you remove the batteries. Mine are stuck in the top end somehow, I can pull the bottom end out about 1cm. Maybe they are soldered at the top? Also, it's confusing why you solder at the circuit board, is that really necessary?

Even my PC has the same problem and I think its the power supply as you said but the technicians are saying power supply/smps is working. I am confused if I should buy a new one. In your case did the PC work for a long duration when it actually started (i.e during the intermittent issue)?

Thanks! i have finder 80.01 and i lose instruction. it work on my device.

Thanks! I fixed the BT5200. I used Panasonic Eneloop AAA 750mAh. Edit: I have recharged the trimmer after replacing the battery. Today, after 10 minutes of shaving, the trimmer started to weaken and the red LED was blinking. Why so short?

thank you very much i do it and work very well !!!

I think Is possibile without welder with rechargeble 🔋AAA 1,2v 750 mah Duracell,what you think??

thank u some much my pc is working now

Thanks a lot, mine is another model, but is very similar.

Thanks a looot man for sharing. Any idea of the dimensions of the batteries?

Didn't work for me I'm afraid. The bit from 1:45 onwards, I have tried to disassemble it with a screwdriver and no matter what, it will not open. I do however have the BT5260 model, but it appears to have been configured in the same way as the model in the video.

What a shitty design.... Doing a complete dissassembly just to get to the batteries.

Thx very helpfull 💪👍

couldn't understand anything that you said.

the PC I have the Fan runs without stop and the PC not POST at all, it's completely dead

Thanks for sharing! Trimmer now as good as new 👍 🇬🇧

thank you bro

That's a great video but Phillips should be ashamed!!

thanx, its good explain of the relay functions

Very nice but you did not schau how to wire through Relay ??? Can you please schau me or send the diagram plan thanks

Please tell where would we get this battery... i.e. welded battery

Great and clear toutorial! Thank You!

Hello... Thank you... This was really helpful. I am facing a problem; after replacing the battery, I couldn't turn off the device. Had to let the battery discharge before fitting everything else in place. Something on the motherboard caught fire that must have been responsible for failure of the switch. Can you confirm.

Hey! I have a similar model and I have put in the new batteries. But the orange light keeps blinking even now. Is there a way to reset it? The trimmer is working fine otherwise

Thnx)

I'm having the same one, it got lot of water stains and dirt accumulated. I was wondering if i can find a disassembly video for this model as I was not sure how to open it, but I was lucky. Thank you!!!

Thank you for the tutorial! I ordered "Eneloop AAA 750 mAh" batteries from a Dutch webshop called NKON. Soldering the batteries was the hardest part. My soldering iron clearly did not have the right wattage. Also remounting the rings took me a while.

A tu instrukcja po Polsku dla BT9290 🇵🇱 th-cam.com/video/7dk15n1HS2Q/w-d-xo.html z dodatkową informacją, jak rozbierać takie sprzęty, aby ich nie uszkodzić

🇺🇸/🇬🇧 and here’s Philips BT9290 revival/refurbishment (internal battery replacement) along with general information how to disassemble this type of equipment without damaging it th-cam.com/video/VJYbwEfq81Q/w-d-xo.html (in English)

1:20 is the important part. slide it down, not up (also works for bt5200). Otherwise you'll break the hinges. Also, the top assembly with plastic rings: look with the light inside the scroller ring and align the plastic bump with a hole at number 10. It's not perfectly 10, there is a slight shift 1mm. Thanks for the video, btw!

Thanks, was about to trash mine !

Hello! Thank you so much. What are you doing with the paint brush in the last part of this tutorial?

Vorsicht. Es ist machbar aber die Lötfahnen der Akkus passen vom Winkel her nicht. Man muss sie also ablöten und die Akkus ausrichten zum wieder anlöten. Auch sind die Lötfahnen zu breit. Das lässt sich aber mit einer normalen Schere bearbeiten. Mit etwas Geschick und Lötfett funktioniert der Rasierer wieder wie am ersten Tag.

Thanks a lot for this video!

really thanks man

Hi... Battery size is "AAA" , 1.2 volt, 750 mAH. This is the actual battery specification. But in my case, i couldn't find batteries with same specification. So i brought "AAA , 1.2 volt with 1100mAH". It is working well. Thanks for watching.

Can you please add details on replacement battery type. Perhaps even a link. Thank you.