- 26
- 37 264
Throttle RDM
เข้าร่วมเมื่อ 19 เม.ย. 2019
Throttle Riding Dirty Mudders
Suzuki king quad brass brake pads
Switching up to the brass knuckle brake pads on the 2020 Suzuki king quad 750
มุมมอง: 58
วีดีโอ
2020 Suzuki king quad 750 head light bulb swap
มุมมอง 4.1K3 ปีที่แล้ว
Changing out the old halogen bulbs to nilight LED bulbs.
Suzuki eiger ball joint replacement
มุมมอง 1.2K4 ปีที่แล้ว
Replacing the lower and upper ball joints both sides on Suzuki eiger 4x4 400.
Suzuki eiger brass brake pads
มุมมอง 1014 ปีที่แล้ว
Installed brass set of brake pads from brass knuckle brake pads doing update when wore down.
2020 Suzuki king quad 750 tie rods
มุมมอง 3144 ปีที่แล้ว
Bent my tie rods less than 20hrs 🤯🤬 pos made new heavy duty.
Suzuki eiger clutch removal
มุมมอง 4.2K4 ปีที่แล้ว
Clutch slipping. Replaced wet clutch and clutch basket
Suzuki Eiger LED head light replacement
มุมมอง 1.6K5 ปีที่แล้ว
Suzuki Eiger LED head light replacement
I wish you could have showed us how you put it in there
Is this a foot shift or cvt?
@@_AlejandroGonzalez_ foot shift
Idk eigers last forever if you don’t do this lol
I got an 05 with under 2000 miles
Honda lasts longer and more reliable then Suzuki
Donde puedo encontrar el kit ??
Thanks for the video!
Can you send a link so I can grab these on Amazon? Thanks!
So my left wheel came out with the axle. Tube is intact. What holds the axle inside the tube?
Alright so I got the bearing racer seized up how could I get that off I just been beating and beating on it
Where did you get the flex pipe from?
When you tightened the a arm bolts,Did you have the suspension jacked up or just hanging down ? Also did the arms move freely after the bolts were tight ? Mine seem to get stuck after tightening the bolts
you said you watcher d-rays video. did you notice which direction he installed the outer dust seal. looked opposite from the way yours was. he had the spring side out. it looks like it should go your way and thats how ive been installing. but not sure its correct
Update on em ? Is the brass riveted or bonded on ?
I have the same bike you no whay my back right tire moves in and out
Sounds like the wheel bearing.
I just rebuilt My Suzuki Eiger 400 but i gots to change the front bearing but also its backfiring could you maybe tell me some reason why it’s doing that
It could be several things maybe the carb is dirty, or the fuel petcock, it might be your air/fuel mixture.
It is a wet clutch you should have soaked the clutches in oil for about 30 min before installing they might have lasted longer.
I soaked them for 24 hrs. It’s just cheap material
The front rotors are the same as honda trx250r rear rotor on their straight axle
Where'd your get your ball joints
I believe I got them on Amazon niche name brand I think they were like 20$ each
Too much air .. need to go smaller pvc some guy put cap on and drilled a few holes
I added a stainless steel wire mesh to help filtration it so tight it helped slow the air intake works perfectly
What tool did you use to hold the clutch basket ? I'm doing the timing chain replacement and can't seem to find a video of it being held ... please help
I used a 1/2 drive impact. The nut is left hand threaded the basket didn’t even spin. But When I first try to take it off with a ratchet and socket the basket would spin. eBay sells a slotted triangle wedge you can shove in to chalk it from moving.
When removing those 30mm and 24mm are they reverse thread ?
I believe they were both left hand threaded I know for sure the 30 mm was but I can’t remember for sure on the 24mm. It makes it really easy if u use an impact trying to do it with a ratchet was a nightmare.
@@throttlerdm934 your right and thanks 👍😎
Hey man , about the 2020 KQ light bulbs ... how do I find them? Thanks alot !
Hey it’s a H4 style bulb . I purchased them on Amazon there is a big variety. Just type in h4 led bulbs
@@throttlerdm934 cool man thanks alot ! Nice bike BTW hopefully I can get me some rims soon
Does a lift kit make a difference?
how’d they hold up
I still have them on the bike it’s been over 15 rides and they are pretty thick still. 💯 never will I ever use any other kind.
@@throttlerdm934 does the braking feel different?
No difference in breaking just squeaks sometimes nothing out of the normal
I have the same bike. What is the part # for the bearings and seals?
James Milczarski not sure I ordered from amazon. I believe its in the video tho.
James Milczarski it shows at the 6 min marker
Throttle RDM your bike set up is pretty sweet! Mine is a 2004 vinson 500. Love the bike just having a reoccurring leak out of the rear left diff seal. Ordered a new seal today hopefully I can install it right this time.
James Milczarski ive seen this happen before its was due to overfilling the diff with fluid. Make sure the fill port bolt is taken out when topping it off.
Throttle RDM I think it is because I didn’t seat the seal properly
Haha awesome man!
Nice video man, do you still have the Eiger going?
Dot Potato yes its still running good bike
Modded, big tires, launching a big utility ATV, then cry about bending stuff. Gee, I wonder why it broke?
Wtf is crying I’m just stating that a hollow tube is not the way to go on tie rods.
looking for a video on a 2004 suzuki eiger wet clutch replacement
Not many out there.
I am fixing to replace the wet clutch on my other eiger I will do a better detailed video.
@@throttlerdm934 did you? I'm about to change out the wet clutch this evening and would like to see your video first if available!
Bro,looks nice i have the same one.i just painted gray with black stock rims and 27 tires.foot shift. I just install the fuel petcock from yamaha raptor 660 2001 to 2005.fit perfect.only 9 bucks on ebay.
PR cc thank you thats the fuel petcock I used too.
0:39 dating-sex-girls.online
Just an update on these pads they did not last. I got about 6-8 rides out of them when I started feeling the clutch slip again about 10 rides in I removed clutch cover and clutch was completely shot to bare metal and had pad fragments all in my motor. Never again will I take the cheap route.
Thank you for this update!
You can use oem honda shoes in these as well.cheaper too . Thats whats in my Eiger.
Only on the eiger auto that works. Foot shift the pads are opposite direction and won’t work without major modifications.
Are they better than the Honda 2020
Silvestre Moreno u already know my feelings towards hondas. Let me know if u need a set made too. Lol 😂
I have a 09 king quad. 400 4x4. My axle moves like yours did on the brake side. So when it moves like that its def the bearings?
Karen Staples bearing
@@throttlerdm934 thank you for getting back to me. I ordered them just in case.
Karen Staples no problem always glad to help.
Bad ass man! Did u need a lift for that wheel and tire set up?
Mr. Estrella no lift just had to trim the front plastic a little bit the dealer trimmed it for me
Where did u get that stainless steel mesh at? And what size???
chris melton i got it at granger I don’t remember the thickness but it’s around 3/32
Thanks for posting. It is nice to know beforehand what I need to do.
Try adjusting the air screw,it's on the bottom of carb,if it never been messed with there will be a metal cap that you'll need to drill out so you can adjust it,also its almost impossible to adjust it with out the special screwdriver,it's like a foot long with a curved end
You can modify a Suzuki Vinson 500 right "rear axel tube" and use the on the Eiger, it uses a cailber/ disc brake, the tube it self will bolt right on and has the mount for the cailber,I think the dude had to shorten or make the tube slightly longer I can't remember, but he made it work with foot brake an the hand brake
skulledmonte84 yes I have done some research on this it should work. Just a long process.
How much did you pay for your led bulbs?
Gill Terrazas I think the were 15-20$
Limit you air that’s going through your snorkel
Thanks for this
What holds the axle into the diff though?
What Jet kit did you order size jets?
twi5t3d7340 not sure what size jets yet hasn’t came in yet but I ordered it from sigma 6 . I gave them a complete detail of what I’ve done to it and they are making a kit just for my quad. I will make a video once it comes in
Btw I have as 02 eiger I will start uploading about it once I get tires on it
Scooter be Me I also have a 02 Eiger that I am working on I’m doing a frame swap on it I broke the A arms where they go welded to the frame so I had to get a new frame maybe I’ll upload some videos on that one too
I would watch that
Ok thanks
How do those mud lights pull
Scooter be Me they do a great job grabs really good. The wheel and tire combo i did are almost exact weight as original so no power loss.