- 19
- 18 334
Lookout Square
เข้าร่วมเมื่อ 3 ต.ค. 2011
Journey to Cape Lookout in my 1987 Squarebody. This is just to share my preparation of the truck and camper to make the trip to the Outer Banks. This is a guys fishing trip that we have done for over 20 years but have taken the last few years off due to the new flounder regulations. This year we have booked our dates for October and now we have to drag out all of our camping/fishing equipment that is specific to this trip.
Taking a drive with the Tremec TR-4050
Out for a drive after Customs by Bigun worked on the Holley EFI. Tremec TR-4050 5 speed transmission swap. Getting ready to pull out the camper that we are going to haul to Cape Lookout. 
มุมมอง: 4 536
วีดีโอ
Gen 6 7.4L in a square body with a Tremec 4050 5 speed behind it
มุมมอง 452ปีที่แล้ว
Just a high-level view of what it takes to put a GEN 6 7.4L in a square body, Chevrolet. All the things that are Gutches that you don’t realize that are different 
Friday morning update
มุมมอง 97ปีที่แล้ว
Thursday night and not much happened with the TREMEC 4050 install
Walk around of the camper going to Cape Lookout
มุมมอง 46ปีที่แล้ว
Walk around of the camper going to Cape Lookout
How does it shift? Can you rip it like a car or is it more of a dump truck
Do you happen to know the differences if there are any inside the 2wd and 4x4 TR-4050’s? I have a 2wd TR-4050 and would like to convert it over to 4x4, curious if it’s just the rear housing or if there’s a shorter output shaft that would have to be changed.
What transfer case?
Very interested in knowing more about your combination. I converted my 85 Silverado from automatic to manual and use the NP 205 transfer case. Is it possible to use my transfer case on a tremec tr-4050? I would hate to have to use the NP 208 again. Thanks and I’m in Gaston County NC where are you located? Thanks buddy and I enjoyed your video.
I’m doing the same swap on my 85 K10. If your 205 has a 10 spline input shaft you can. The tr4050 has a 23 spline output shaft. They make an adapter for the 23 to a 10 spline shaft. I happen to find a 205 passenger side drop from a dodge that has the 23 spline input shaft and will bolt directly to the tr4050.
Those gear shifts look crispy 💦
I just found your channel while I was searching for information on installing a gen6 454 and TR4050 in a squarebody. I have a 1985 K10 that is the same color inside and out as yours. I recently picked up a Gen6 for it. Taking out the stock 305 and 700r4. I got a np205 out of a dodge that is supposed to bolt right up to the TR4050
How are you liking this setup now that it has been a few months?
Where did you find the instructions for that adapter? Can't seem to find it
About to install the 4050 in my 77 k10, going from the sm465. Thoughts so far on your install?
Just got myself a 76 looking to possibly go this route if you would keep me updated how you like it?!!
So far so good on my install. Works great
Glad to hear someone else likes this transmission. I want to get one for my square as well, 86 C10 with a sm465. Just would like to know what the rpms are (roughly) around 75 mph with the 4050!
What transfer case did you put on it ? Also did you had to adapt or transmission comes already as it is seen ? I have the opportunity to get a new one but would like to use my np208 which is actually connected to a th700
Sorry that I didn’t see your message about the transfer case. I used an NP205. You have to use the older version. I think it is pre-1986.
How exciting to see haha Can't wait to get my TR4050 from SST for my Square too! Looks like it drives exactly as anticipated, what a unit. Thanks for the video mate, cheers from Australia
Typical TH-cam short barely a beginning and absolutely no ending...